manualshive.com logo in svg

Forkardt 3QLCLM, Руководство по эксплуатации

Поделиться
Скачать
Forkardt 3QLCLM Скачать руководство пользователя страница 32

Table of contents 

3QLCLM 

Edition: 04/2014 

32 

6.2 

Mounting of the power chuck 

Remove  any  chips  from  the  machine  spindle  before  mounting  the  power  chuck.  Clean  the  register 
and locating faces of the adapter flange! 

6.3 Procedure for mounting the power chuck 

Attention: 

If a mobile hoist which can be moved in all directions is available for mounting the power 
chuck, observe the following points: The working load of the hoist must be at least the weight 
of the power chuck! 

Attention: 

 

Use the mounting hook to mount the power chuck on the hoist and 
  level it with the spindle. 
The mounting hook must correspond to the conditions in accordance with DIN 6890 
! 

Attention: 

Remove any chips from the machine spindle before mounting the power chuck. 
Clean the register and locating faces of the adapter flange (adapter disc)! 

However, in case the machine’s chucking equipment is frequently changed, the draw tube should 
be  screwed  into  the  thread  of  the  3QLCLM  power  chuck  and  Loctite  290  should  be  used  to 
secure it against loosening! 

When screwing the draw tube in the chuck piston, take care not to damage the O -ring! 

Machine spindle

 

Power chuck including 

screwed draw tube

Chuck and mounting screws

Содержание 3QLCLM



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды