Focal Point GRANGE MULTIFLUE Скачать руководство пользователя страница 17

Lay out the pebbles and put the 4

largest to one side. Place any six

of  the  smaller  pebbles  on  the

front  row  of  the  matrix.  Ensure

the pebbles are firmly against the

side cheeks as shown in the pho-

tograph. If necessary, pull the peb-

bles  forward  slightly  to  ensure

their rear edges do not overhang

the flame ports. The edges of the

pebbles  MUST NOT be  allowed

to enter the flame ports.

Place the middle row of four larger pebbles onto the supports in the matrix, over

the top of the holes and partially on top of the front pebbles. Ensure the pebbles

are not turned sideways, such that they actually enter the holes.

Place the rear row of five pebbles on the flat posts of the matrix and up against the

middle row making sure there is a gap between them. It may be necessary to change

the orientation of these by 90 degrees. Note: The pebbles must not be crammed

together, or inserted into the holes in the matrix. A well laid out,  generously spaced

pebble layout will give the best results.

Make sure the flames travel through the pebbles and are not obstructed by them. No flames should hit the sides of the firebox

IMPORTANT :  

The fire is designed to operate correctly with the pebbles supplied when assembled according to the

instructions. Never add to the fifteen pebbles, or change them for a different type. Never throw rubbish or other

matter onto the fuel bed. Due to the light colour of the pebbles, some discolouration/sooting is to be expected dur-

ing normal use. 

This fire is supplied with 11 ceramic moulded coals. 

Fit the tapered brick pad into the securing brackets in the upper area of the fire-

box. Place the large brick panel against the rear of the firebox.

Place the ceramic combustion matrix onto the burner.

Lay out the coals and put the 4

largest to one side.

Place the front row of five small-

er coals on to the matrix. Ensure

that  the  coals  are  lined  up  with

the  port  walls.  The  rear  two

smaller coals are to be position in

the centre and pushed back. The

edges of the coals MUST NOT be

allowed to enter the flame ports.

5

© 2016 Focal Point Fires plc.

7.1 FUEL BED LAYOUT - PEBBLE EFFECT - CONTINUED

GB IE

Figure 14

Figure 16

Figure 15

7.2 FUEL BED LAYOUT - ROUNDED COAL EFFECT

Figure 17

Figure 19

Figure 18

Содержание GRANGE MULTIFLUE





















Отзывы: