background image

This fire is supplied with 15 ceramic ripped coals. 

Fit the tapered brick pad into the securing brackets in the upper area of the fire-

box. Place the large brick panel against the rear of the firebox.

Place the ceramic combustion matrix onto the burner and the ceramic side cheeks

onto the matrix.

Place the front row of six coals

on  to  the  matrix.  Ensure  the

coals are firmly against the side

cheeks as shown in the photo-

graph. If necessary, pull the coals forward slightly to ensure their rear edges do not

overhang the flame ports. Corners or rough edges MUST NOT be allowed to enter

the flame ports. If in any doubt pull the coals as far forward as possible.

Place four coals onto the flats on the rear of the matrix. Making sure that the flat

sides are firmly against the brick panel and side cheeks as shown.

Place the five remaining coals on the flat pillars of the coal bed ensuring there is a

10mm gap between them.

The coals must not be crammed together, or inserted into the holes in the matrix.

A well laid out,  generously spaced coal layout will give the best results.

When lit the flames should not be hitting the sides of the firebox, if so adjust as nec-

essary. No coals should be directly above a flame port.

IMPORTANT :  The fire is designed to operate correctly with the coals supplied when assembled according to the

instructions. Never add to the fifteen coals, or change them for a different type. Never throw rubbish or other matter

onto the coal bed.

This fire is supplied with 15 ceramic pebbles.  Lay the pabbles out and put the

four largest to one side. The pebbles may vary slightly in size, shape and colour, in

order to allow a realistic layout. Fit the tapered brick pad into the securing brack-

ets in the upper area of the firebox. Place the large brick panel against the rear of

the firebox.

Place the ceramic combustion matrix onto the burner and the ceramic side cheeks

onto the matrix.

4

© 2016 Focal Point Fires plc.

7.1 FUEL BED LAYOUT - PEBBLE EFFECT

7.0 FUEL BED LAYOUT - RIPPED COAL EFFECT

GB IE

Figure 7

Figure 8

Figure 10

Figure 9

Figure 11

Figure 12

Figure 13

Содержание GRANGE MULTIFLUE





















Отзывы: