No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the
same room or space must be taken into consideration when assessing ventilation. If spillage is detected when commissioning the appli-
ance, then amongst other problems there may be insufficient natural ventilation for correct operation of the flue. If the appliance does
not spill with the windows open, but spillage is detected with the windows closed, this demonstrates a lack of natural ventilation. If
spillage is still detected with the windows open, the flue is at fault. Installation of an air brick is the best solution to lack of ventilation.
Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2. Vents fitted under or within the immediate vicinity of the
appliance must not be used as adverse effects to the operation of the ODS may occur. Spillage detected during commissioning is almost
always a result of poor flue performance that cannot be corrected by any amount of ventilation. For Republic of Ireland ventilation may
be required, see IS 813, ICP3, IS 327, and any other rules in force.
This appliance can be fitted into a number of proprietary flue
boxes provided that the minimum dimensions shown in figure 2
are complied with.
Constructional Note: The frame of the fire, any back panel or
other infill panels, and the flue box must be sealed together so that
there is no possibility of leakage between them. Adequate clear-
ances to combustible materials (e.g. false chimney breast con-
struction) must be maintained.
The manufacturers’ instructions for fitting the prefabri-
cated box shall be complied with at all times. To fit the fire
using the cable fixing kit, some minor adaption may be necessary
for certain flue boxes. A check should be made to ensure the fire-
box does not obscure the flue box outlet. The firebox, base of the
flue box, and hearth below may be drilled to allow plugs and
screws to secure installation. It is important that the sealing
requirements of the appliance are met at all times and that the flue
box is well sealed to any back or infill panel. Note: The DEPTH
dimension is inclusive of any back or infill panel.
Stand the carton the right way up, cut the strapping bands and remove the top endcap. Read all the instructions before continuing to
unpack or install this appliance. Remove the box containing the firefront, and the bags containing the ceramic components. Remove the
cardboard packing pieces, and any other bags or boxes containing fittings or other parts. When all loose parts have been removed, the
outer sleeve may be lifted off to reveal the appliance. Check that the components supplied correlate with the component checklist given
in section 7.1. Please dispose of all the packaging materials at your local recycling centre.
5.0 VENTILATION
GB IE
6.0 PREFABRICATED FLUE BOXES
125mm min internal dia. twin wall flue
Radiant models:
128mm min
depth
Convector
models:
140mm min
depth
Radiant models: 350mm min opening width
Convector models: 380mm min opening width
540mm
min height
Figure 2
7.0 UNPACKING THE APPLIANCE
7.1 COMPONENT CHECKLIST
QUANTITY
DESCRIPTION
1
Firebox and burner tray assembly
1
Decorative frame
1
Firefront
1
Black Moulded ceramic fibre combustion matrix (coal effect versions only)
1
Beige Moulded ceramic fibre combustion matrix (Pebble effect version only)
11
Individual ceramic coals (rounded coal effect version only)
15
Individual ceramic coals (ripped coal effect version only)
15
Individual ceramic pebbles (pebble effect version only)
2
Ceramic fibre side cheeks (pebble effect & ripped coal effect)
1
Ceramic rear panel
1
Ceramic taper pad (radiant models only)
1
Remote control handset (remote control models only)
1
Cable fixing kit; 2 cables, 2 tensioners, 2 cable clamps, 4 fixing eyes, 4 wall plugs
1
Sealing grommet
3
Lengths of adhesive sealing strip
1
Self tapping screw pack; 4 No.8 x 5/16
1
Spigot restrictor
1
Deflector baffle
1
Set of manufacturers instructions
1
Slide control position marking sticker (slide control models only)
1
Slide control knob and M4 Nyloc nut (slide control models only)
5
© 2016 Focal Point Fires plc.
