The pilot is visible through the viewing hole which is located at the lower left hand side of the fuel
bed. The fire features a ‘twin spark’ ignition system to aid lighting, Push the control knob in fully
and turn anti-clockwise through both of the SPARK positions, keeping fully depressed, hold there
for a few seconds. If the fire has not been used for some time, hold the knob in this position for
longer, to allow any air in the pipes to be purged. Continue turning anti-clockwise through the
spark clicks to the nine o’clock position, ensuring the pilot has lit. If not, return the knob clock-
wise, and repeat.
When the pilot lights after one of the two sparks, keep the knob depressed in the nine o’clock
position for approximately ten seconds. Now release the knob and the pilot should stay alight. If
the pilot is extinguished during use, wait three minutes before repeating the ignition procedure. To
achieve the HIGH setting, push the control knob in slightly and continue turning anti-clockwise to
the high position. The main burner should light after a few seconds. To decrease the setting to LOW, push the knob in slightly and turn
the control knob clockwise to the low setting. To turn to the pilot only position from the HIGH or LOW positions, press the control
knob in, and return to the nine o’clock position and release. To turn the fire OFF, keep the knob pressed in, return to the off position
and release.
The pilot is visible through the left hand side of the front ceramic strip. Rotate the coals or pebbles for
good viewing.
Push the slide control knob fully downwards to the SPARK position, and hold there for a few seconds,
until the pilot light stays on. When the pilot light has established, release the slide control knob and it
will return to the LOW flame setting. If the pilot is extinguished during use, wait three minutes before
repeating the ignition procedure.
To achieve the HIGH setting, move the slide control knob upwards to the HIGH flame setting. The fire
can also be set to operate anywhere between HIGH and LOW by moving the control knob to an inter-
mediate position.
To turn the fire OFF, move the slide control knob upwards fully to the position marked ‘O’.
The pilot is visible through the left hand side of the ceramic fuel bed.
When cold, the coals or pebbles may be rotated for good viewing.
Turn the main burner control (shown on left hand side of control valve) knob
fully anti-clockwise.
Turn ignition knob (shown on right hand side of control valve) slightly left
towards the ignition position until reaching the stop, press down and hold for
5 seconds (only pilot gas is flowing)
Continue pressing down the knob while turning further to the left to activate
the piezo spark, continue to hold the knob down for a further 10 seconds
after the pilot has been lit. If the pilot does not light repeat the previous steps.
Upon lighting and after the further 10 seconds, release the knob and turn further to the left to the
ON position. The main burner will light and be controlled in accordance with the main burner con-
trol knob setting. Adjust the main burner control knob to the desired setting.
If the pilot is extinguished during use of the fire, you MUST wait ten minutes before repeating the
ignition procedure.
To turn the main burner OFF whilst keeping the pilot flame lit, turn the ignition control knob to the
pilot position then only the pilot will remain lit.
To shut the fire off completely, press the ignition control knob down and continue turning to the
right from the pilot position to the OFF position.
A safety interlock prevents re-ignition of the pilot flame until the thermocouple has cooled suffi-
ciently to allow the magnetic valve unit to reset itself.
The remote control unit allows operation of the main burner setting between maximum and pilot
only setting. It does not permanently turn the pilot on or off.
The remote control handset incorporates an inbuilt safety feature to prevent the main burner being
activated or turned up accidentally. It is necessary to press button 1 and 2 (see figure 18) simultane-
ously to turn the fire up.
To turn the fire down press button 3 only.
FIN:
A
12.1 OPERATING THE FIRE - MANUAL CONTROL MODELS
GB IE
9
© 2013 Focal Point Fires plc.
Figure 15
12.2 OPERATING THE FIRE - SLIDE CONTROL MODELS
Figure 16
12.3 OPERATING THE FIRE - REMOTE CONTROL MODELS
FIN:
A
1
2
3
FIN:
A
:
Figure 18
Figure 17
