No purpose provided ventilation is normally required for this appliance. The requirements of other appliances operating in the
same room or space must be taken into consideration when assessing ventilation. If spillage is detected when commissioning the appli-
ance, then amongst other problems there may be insufficient natural ventilation for correct operation of the flue. If the appliance does
not spill with the windows open, but spillage is detected with the windows closed, this demonstrates a lack of natural ventilation. If
spillage is still detected with the windows open, the flue is at fault. Installation of an air brick is the best solution to lack of ventilation.
Any ventilation fitted must comply with BS 5871 part 2 and BS 5440 part 2. Vents fitted under or within the immediate vicinity of the
appliance must not be used as adverse effects to the operation of the ODS may occur. Spillage detected during commissioning is almost
always a result of poor flue performance that cannot be corrected by any amount of ventilation. For Republic of Ireland ventilation may
be required, see IS 813, ICP3, IS 327, and any other rules in force.
This appliance can be fitted into a number of proprietary flue boxes
provided that the minimum dimensions shown in figure 2 are com-
plied with.
Constructional Note: The frame of the fire, any back panel or
other infill panels, and the flue box must be sealed together so that
there is no possibility of leakage between them. Adequate clear-
ances to combustible materials (e.g. false chimney breast construc-
tion) must be maintained.
The manufacturers’ instructions for fitting the prefabri-
cated box shall be complied with at all times. To fit the fire
using the cable fixing kit, some minor adaption may be necessary
for certain flue boxes. A check should be made to ensure the fire-
box does not obscure the flue box outlet. The firebox, base of the
flue box, and hearth below may be drilled to allow plugs and screws
to secure installation. It is important that the sealing requirements
of the appliance are met at all times and that the flue box is well
sealed to any back or infill panel. Note: The DEPTH dimension is
inclusive of any back or infill panel.
Stand the carton the right way up, cut the strapping bands and remove the top endcap. Read all the instructions before continuing to unpack
or install this appliance.
Remove the box containing the firefront, and the bags containing the ceramic components. Remove the cardboard packing pieces, and any other
bags or boxes containing fittings or other parts. When all loose parts have been removed, the outer sleeve may be lifted off to reveal the appli-
ance. Check that the components supplied correlate with the component checklist given in section 7.1. Please dispose of all the packaging mate-
rials at your local recycling centre.
5.0 VENTILATION
GB IE
6.0 PREFABRICATED FLUE BOXES
7.0 UNPACKING THE APPLIANCE
7.1 COMPONENT CHECKLIST
QUANTITY
DESCRIPTION
1
Firebox and burner tray assembly
1
Decorative frame
1
Firefront (fret)
1
Moulded ceramic fibre combustion matrix
1
Moulded ceramic front strip
16
Individual ceramic coals (Coal models only)
16
Individual ceramic pebbles (Pebble models only)
9
Individual ceramic logs (Log models only)
1
Slide control knob and M4 Nyloc nut (Slide control models only)
1
Cable fixing kit; 2 cables, 2 tensioners, 2 cable clamps, 4 eyebolts, 4 wall plugs
1
Sealing grommet
3
Lengths of adhesive sealing strip
1
Self tapping screw pack; 4 No8 x 5/16
1
Remote control Handset (Remote control models only)
1
Set of manufacturers instructions
5
© 2013 Focal Point Fires plc.
125mm min internal dia twin wall flue
Radiant models :
250mm min depth
Convector models :
265mm min depth
Radiant models : 375mm min opening width
Convector models : 390mm min opening width
Radiant
models :
570mm min
height
Convector
models :
545mm min
height
Figure 2
