FoamPRO AccuMax 3040 Скачать руководство пользователя страница 43

Страница: 43 / 60

Maintenance Procedures

After each use

: Flush FoamPro AccuMax SP foam

pumps with fresh water (required if using other than

Class A foam concentrate).

Monthly

: Inspect wiring, hoses, flowmeters, and

connections for tightness, corrosion, leaks and/or

damage.

Monthly:

Check and top off the hydraulic oil

reservoir as needed.

NOTE: The hydraulic oil should not require refilling.

If the system requires oil regularly, an undetected

leak is present in the system.

Monthly

: Ensure oil cooler intake and cooler

surface is free of obstructions.

Monthly

: Remove and clean the foam strainer

screen(s). Flush as required.

Bi-Annually

: Drain and refill the hydraulic oil

reservoir with proper hydraulic oil as noted in

Section 4.

NOTE: Other types of hydraulic fluids are too

viscous for proper load sense compensator

operation. Do not mix hydraulic fluid types.

Bi-Annually:

Replace the hydraulic filter element by

unscrewing the filter housing and replacing the

element. After filter element has been changed,

energize the system and check filter for leaks. At

this time, also clean and/or replace all filters and

screens in the hydraulic system.

3020 and 3040

3800-0100

3060 thru 3300

3800-0101

NOTE: Dirt is the “enemy” of any hydraulic system.

Use care when installing and maintaining system to

keep dirt particles from entering the hydraulic

system.

WARNING: Release all pressure within the system

before servicing any of its components.

Installation and Operation Manual

AccuMax SP

Maintenance

Содержание AccuMax 3040





























































Результаты поиска

Содержание AccuMax 3040

Отзывы:

Похожие инструкции для AccuMax 3040

Бренды по названию

Популярные бренды

FoamPRO AccuMax 3040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AccuMax 3040

Отзывы:

Похожие инструкции для AccuMax 3040

Бренды по названию

Популярные бренды