FoamPRO AccuMax 3040 Скачать руководство пользователя страница 45

Страница: 45 / 60

Installation and Operation Manual

AccuMax SP

Symptom

Probable Cause(s)

Corrective Action

Pump does not run.

ERR.HY

Hydraulic pump not properly

Check and attach cables

display.

connected to driver box.

to pump and driver box.

Truck hydraulics not running.

Engage hydraulic PTO.

Pump runs but produces no flow.

Pump is not primed.

See Foam Pump Priming

procedures in Section 10.

Pump loses prime, chattering

Air leak in suction hose or inlet

Remove suction hose and test

noise, pressure fluctuates.

fittings.

for leaks by pressurizing hose

with water. Make sure thread

sealant has been used on all

fittings.

Suction line is blocked, collapsed.

Remove suction line and inspect

it for a loose liner or debris

lodged in hose. Avoid all un-

necessary bends. Do not kink

hose.

Clogged suction strainer.

Clean strainer.

Defective control cable or

Replace control cable.

bent pins.

Figure 14-2

Electrical Wiring Diagram

Troubleshooting Continued on Next Page

Pump runs for 8 to 10 seconds

then shuts down.

ERR.HY

may

be flashed on display.

Flowmeter

Cable

Flowmeter

Control

Cable

To 12 or 24 VDC

Small

Beads

Digital Display

Control Module

Large

Beads

Foam

Flowmeter

Foam Tank

Low-Level

Sensor

Содержание AccuMax 3040





























































Результаты поиска

Содержание AccuMax 3040

Отзывы:

Бренды по названию

Популярные бренды

FoamPRO AccuMax 3040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AccuMax 3040

Отзывы:

Бренды по названию

Популярные бренды