FoamPRO AccuMax 3040 Скачать руководство пользователя страница 41

Страница: 41 / 60

Installation and Operation Manual

AccuMax SP

Simulated Flow Operation Summary

How to

Display

Action

4. Place a suitable container

under the CAL/FLUSH outlet

tube. Place the CAL/INJECT

valve in the CAL/FLUSH

position.Press the

FOAM

button.The foam pump will

operate and foam concentrate

will be discharged from the

outlet tube.

NOTE: FoamPro must be in

Simulated Flow Mode

5. Press both rate adjustment

buttons at the same time.

The

symbol will leave the

display and the FoamPro will

operate automatically from

the flow sensor signal.

Turning the apparatus

Master or Battery switch off

will also turn off the

Simulated Flow Function.

The next time the power is

turned on, the FoamPro will

return to the original

automatic default settings.

4. Empty the Foam Tank.

5. Turn the Simulated Flow

Function off and return to

automatic operation.

830

Содержание AccuMax 3040





























































Результаты поиска

Содержание AccuMax 3040

Отзывы:

Похожие инструкции для AccuMax 3040

Бренды по названию

Популярные бренды

FoamPRO AccuMax 3040, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AccuMax 3040

Отзывы:

Похожие инструкции для AccuMax 3040

Бренды по названию

Популярные бренды