Fluo FSS 241 EI/JDF-N3 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 33

background image

24

Step 1: Choosing installation location

Recommend the installation location to the client and then confirm it with the client.

Step 2: Install wall-mounting frame

1. Hang the wall-mounting frame on the wall; adjust it in horizontal position with the level
meter and then point out the screw fixing holes on the wall .
2. Drill the screw fixing holes on the wall with impact drill (the specification of drill head
should be the same as the plastic expansion particle) and then fill the plastic expansion

particles in the holes.

3. Fix the wall-mounting frame on the wall with tapping screws (ST4.2X25TA) and then
check if the frame is firmly inatalled by pulling the frame. If the plastic expansion particle
is loose, please drill another fixing hole nearby.

Step 3: Open piping hole

1. Choose the position of piping hole according to the direction of outlet pipe. The position
of piping hole should be a little lower than the wall-mounted frame, shown as below.

Left

Wall

Φ55/Φ70

Right

Mark in the middle of it

Level meter

Rear piping hole

Wall

Space

to the

wall

above

150mm

Space

to the

wall

above

150mm

Φ55/Φ70

Rear piping hole

Dimension: 1081x327x248

Left

Wall

Φ55

Right

Mark in the middle of it

Level meter

Rear piping hole

Wall

Space

to the

wall

above

150mm

Space

to the

wall

above

150mm

Φ55

Rear piping hole

Left

Wall

Φ55

Right

Mark in the middle of it

Level meter

Rear piping hole

Wall

Space

to the

wall

above

150mm

Space

to the

wall

above

150mm

Φ55

Rear piping hole

Dimension: 721x274x195

Dimension: 792x279x195

Left

Wall

Φ55

Right

Mark in the middle of it

Level meter

Rear piping hole

Wall

Space

to the

wall

above

150mm

Space

to the

wall

above

150mm

Φ55

Rear piping hole

Left

Wall

Φ55/Φ70

Right

Mark in the middle of it

Level meter

Rear piping hole

Wall

Space

to the

wall

above

150mm

Space

to the

wall

above

150mm

Φ55/Φ70

Rear piping hole

Dimension: 850x291x203

Dimension: 972x302x224

Installation of indoor unit

«
...
24
25
26
27
28
...
»

Содержание FSS 241 EI/JDF-N3


































Отзывы:

Нет отзывов

Похожие инструкции для FSS 241 EI/JDF-N3

Бренд: Samsung Страницы: 40

Бренд: Dimplex Страницы: 12

Бренд: GE Страницы: 56

Бренд: Uberhaus Страницы: 29

Бренд: Movincool Страницы: 50

Бренд: Amana Страницы: 44

Бренд: Pure n Natural Systems Страницы: 4

Бренд: Nortek Страницы: 16

Бренд: TCL Страницы: 40

Бренд: Gree Страницы: 25

Бренд: Danby Страницы: 44

Бренд: ClearWave Air Страницы: 12

TA36FFLL-1232IA

Бренд: Tesla Страницы: 288

Бренд: M Confort Страницы: 51

Бренд: LifeWise Страницы: 2

uniblock ZM Series

Бренд: Zanotti Страницы: 76

Бренд: Panasonic Страницы: 40

Бренд: Panasonic Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды