Fluo FSS 241 EI/JDF-N3 Скачать руководство пользователя страница 31

Страница: 31 / 33

Check according to the following requirement after finishing installation.

Check after installation

Items to be checked

Possible malfunction

Has the unit been installed firmly?

The unit may drop, shake or emit noise

Have you done the refrigerant leakage
test?

It may cause in sufficient cooling (heating)

capacity.

Is heat insulation of pipeline sufficient?

It may cause condensation and water dripping.

Is water drained well?

It may cause condensation and water dripping.

Is the voltage of power supply according
to the voltage marked on the

nameplate?

It may cause malfunction or damaging the parts.

Is electric wiring and pipeline installed

correctly?

It may cause malfunction or damaging the parts.

Is the unit grounded securely?

It may cause electric leakage.

Does the power cord follow the

specification?

It may cause malfunction or damaging the parts.

Is there any obstruction in the air inlet

and outlet?

It may cause in sufficient cooling(heating)

capacity.

The dust and sundries caused during

installation are removed?

It may cause malfunction or damaging the parts.

The gas valve and liquid valve of
connection pipe are open completely?

It may cause in sufficient cooling(heating)

capacity.

Содержание FSS 241 EI/JDF-N3


































Результаты поиска

Содержание FSS 241 EI/JDF-N3

Отзывы:

Похожие инструкции для FSS 241 EI/JDF-N3

Бренды по названию

Популярные бренды

Fluo FSS 241 EI/JDF-N3, Руководство пользователя

Результаты поиска

Содержание FSS 241 EI/JDF-N3

Отзывы:

Похожие инструкции для FSS 241 EI/JDF-N3

Бренды по названию

Популярные бренды