Fluke MicroMapper Pro Скачать руководство пользователя страница 3

Страница: 3 / 20

•

The tester is not intended to be connected to active telephone or
network cables, systems, or equipment, including ISDN devices.
Prolonged exposure to the voltages applied by these interfaces
may damage the tester.

•

Do not use the tester if it operates abnormally. Protection may
be impaired.

Caution

To ensure maximum accuracy of test results replace the batteries
as soon as the low battery (

) indicator appears.

Contacting Fluke Networks

•

Australia: 61 (2) 8850-3333 or 61 (3) 9329-0244

•

Beijing: 86 (10) 6512-3435

•

Brazil: 11 3044 1277

•

Canada: 1-800-363-5853

•

Europe: +44-(0)1923-281-300

•

Hong Kong: 852 2721-3228

•

Japan: 03-3434-0510

•

Korea: 82 2 539-6311

•

Singapore: 65 6799-5566

•

Taiwan: (886) 2-227-83199

•

USA: 1-800-283-5853

•

Anywhere in the world: +1-425-446-4519

Visit our website for a complete list of phone numbers.

www.flukenetworks.com

[email protected]

+1-425-446-4519

Содержание MicroMapper Pro





















Результаты поиска

Содержание MicroMapper Pro

Отзывы:

Похожие инструкции для MicroMapper Pro

Бренды по названию

Популярные бренды

Fluke MicroMapper Pro, Инструкция

Результаты поиска

Содержание MicroMapper Pro

Отзывы:

Похожие инструкции для MicroMapper Pro

Бренды по названию

Популярные бренды