Fluke MicroMapper Pro Скачать руководство пользователя страница 17

Страница: 17 / 20

Maintenance

Warning

To avoid possible fire, electric shock, personal injury, or damage
to the tester do not open the case. No user-serviceable parts are
inside.

Cleaning

Clean the display with glass cleaner and a soft, lint-free cloth. Clean the case
with a soft cloth dampened with water or water and a mild soap.

Caution

To avoid damaging the display or the case, do not use solvents
or abrasive cleansers.

Replacing the Batteries

See “Battery Installation and Status”.

Restoring Factory Defaults

To restore the user-defined length calibration parameters and other settings
to the factory defaults, do the following:

1 Turn off the tester.

2 Hold down

and

; then press

and wait until the display shows

rESEt

(reset) before releasing the

and

keys.

3 Press

to select

yES

(yes); then press

Содержание MicroMapper Pro





















Результаты поиска

Содержание MicroMapper Pro

Отзывы:

Похожие инструкции для MicroMapper Pro

Бренды по названию

Популярные бренды

Fluke MicroMapper Pro, Инструкция

Результаты поиска

Содержание MicroMapper Pro

Отзывы:

Похожие инструкции для MicroMapper Pro

Бренды по названию

Популярные бренды