Fluke 9100 Series Скачать руководство пользователя страница 9

Страница: 9 / 74

1-1

Section 1

Introduction and Specifications

INTRODUCTION

This manual presents service information for the 9100A-017 Vector Output

I/O Module. Included are a theory of operation, general maintenance

procedures, performance tests, troubleshooting information, a list of

replacement parts, and schematic diagrams.

SPECIFICATIONS

Table 1-1 contains the specifications for the Vector Output I/O Module.

NOTE

Output specifications for Table 1-1 were obtained using

the Y9100-102 Card Edge Interface Module into 10 LSTTL

loads. Results may vary depending on the impedance,

length, and shielding of the connector used. (Output

timing is measured at 50% of signal amplitude.)

Table 1-1. Vector Output I/O Module Specifications

______________________________________________________________________________

VECTOR OUTPUT I/O MODULE OUTPUT

(into 10 LSTTL loads with card edge connector attached):

Module Vector Size ......................... 8192 vectors, 40 channels wide.

Maximum Vector Pattern (4 Modules) ......... 8192 vectors, 160 channels wide.

Vector Looping ............................. Up to 65536 repetitions of

one vector set.

Output Logic Levels:

High ................................... 3.7V minimum (6.0 mA source).

Low .................................... 0.4V maximum (6.0 mA sink).

INT CLK (internal clock) ................... 1, 5, 10, or 20 MHz (±100

ppm).

DR CLK (external clock) .................... 25 MHz maximum. (This frequency

maximum may be exceeded in some

cases based upon application

and hardware interfacing.)

Clock to Vector Out (tdel):

INT CLK Out to Vector Out Delay ........ 37 ns typical, 45 ns maximum.

DR CLK In to Vector Out Delay .......... 50 ns typical, 58 ns maximum.

______________________________________________________________________________

Содержание 9100 Series










































































Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды

Fluke 9100 Series, Руководство по обслуживанию

Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды