Fluke 9100 Series Скачать руководство пользователя

Страница: 30 / 74

2/Theory of Operation

2-18

Table 2-5. Connector Code Examples

_________________________________________________________________

CODE READ MEANING

_________________________________________________________________

$F3 No clip on B side, 20-pin clip on A side

$4F 24-pin clip on B side, no clip on A side

$E1 40-pin clip installed

$14 16-pin clip on B side, 24-pin clip on A side

$FF No clips installed

________________________________________________________________

qualified RD- and WR- are also available to the output section. However,

there is a separate data bus for the output section that is selected

when LAT-A7 is low.

Two ICs are required to perform the data bus interfacing: a 74ALS245

Octal 3-State Transceiver (U24) and the 74LS31 delay elements (U29).

Both devices are located on the Main PCA.

The TOPDATA Bus (used by the output section) is isolated from A-D-BUS

(used by the input section) by U24. If a read or write access is made to

any address of the output section (A7 = 0), LAT-A7 remains low, thereby

providing an enable signal to U24 pin 19 (G-). The WR- signal determines

the direction of data travel. If WR- is high, the data passes from the

TOPDATA bus to A-D-BUS for a read. If WR- is low, the data passes in the

other direction for a write.

Some register control signals (such as COMMAND0- and COMMAND1- for U5

and U6 of the Top PCA) use the rising edge of WR- to latch data. Since

the WR- signal also controls the direction of the TOPDATA bus through

}U24, U29 provides a nominal 46.5 ns delay to the direction control

signal (WR-DLY-) on U24. This insures that, during accesses to the

output section, the data bus is held in the correct direction by U24

while the rising edge of RD- or WR- latches the data.

ADDRESSING

All addresses with A7 low are reserved for the output section. Since A3

through A1 only go to the custom chips for use as addresses and STROBE-

is only active for addresses with LDS- active (address bit 0 = 1), the

address space is effectively limited to $DOX01 through $DOX71.

Table 2-6 lists the output section addresses and the signals (or

registers) that are affected by accessing the address for both reads and

writes.

Performing a write to $DOX01 causes the COMMAND0- output of U10 (Top

PCA) to toggle, thereby latching the data on the bus into the U5

on in this section for more information.) When a read is performed at

this address, the Vector Drive Status Nybble is returned from U25 (Main

PCA). (See the heading, “Drive Status Functional Block”, further on in

this section and Table 2-10 for more information.)

Содержание 9100 Series










































































Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды

Fluke 9100 Series, Руководство по обслуживанию

Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды