Fluke 9100 Series Скачать руководство пользователя страница 10

Страница: 10 / 74

1/Introduction and Specifications

1-2

Table 1-1. Vector Output I/O Module Specifications (cont.)

______________________________________________________________________________

WAIT (Handshake) Setup Time (twsu) ......... 42.5 ns maximum (35 ns typical)

from WAIT acknowledgement until

next clock cycle drives vector.

If the setup time is not met,

the next clock drives out the

vector. Minimum WAIT pulse

width is 10 ns.

Single Module Channel to Channel Skew* ..... 6 ns maximum (1 ns typical).

Module to Module Channel Skew* ............. 10 ns maximum (1 ns typical).

TRISTATE-:

Activation (txout) ..................... Output source/sink released 25

ns maximum (20 ns typical)

after TRISTATE- goes low.

Minimum TRISTATE- pulse width

is 10 ns.

Recovery (txsu) ........................ TRISTATE- must go high no later

than 5 ns after the rising edge

of the INT CLK or no later than

10 ns after the programmed edge

of DR CLK for the vector to be

output by that clock, otherwise

that vector is only driven

internally and the output is

held tri-stated, effectively

skipping that vector.

Output Series Termination .................. 33 Ohms

Capture Clock:**

INT CLK ................................ Capture Clock clocks 42.5 ns

±5 ns after the falling edge

of INT CLK.

DR CLK ................................. Capture Clock clocks 55 ns

±10 ns after non-clocking edge

of DR CLK (approximate 50% duty

cycle).

START, STOP, and ENABLE:

START, STOP Pulse Width .................... 10 ns minimum.

INT CLK

START Setup Time .................. 30 ns minimum.

STOP Setup Time ................... 30 ns minimum.

ENABLE Setup Time ................. 25 ns minimum.

ENABLE Hold Time .................. 20 ns minimum.

______________________________________________________________________________

Skew measurement assumes equal loading. Differences in capacitance

may affect results.

Capture clock may be adjusted in approximate 15 ns steps by using the

setoffset command (see the 9100 Series TL/1 Reference Manual).

______________________________________________________________________________

Содержание 9100 Series










































































Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды

Fluke 9100 Series, Руководство по обслуживанию

Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды