Fluke 9100 Series Скачать руководство пользователя страница 35

Страница: 35 / 74

2/Theory of Operation

2-23

determines if the vector drive clock should be always enabled or if the

external ENABLE should be used. Bit 2 determines if the vector output

should be “force” started (no external start required) or if the

external START is required. Bit 1 determines if the external STOP signal

should terminate vector driving or not. Bit 0 is unused (the address and

position of this bit are used for clearing START-ENA).

DRIVE CLOCK SELECTION

Five different clock sources are available for use by the output

section: CLKP (from DR CLK), PSYN- (Pod Sync), INT-OSC, RAM-STROBE, and

DECREMENT (used for vector RAM loading). These clocks are input to an

8-Input Multiplexer (U14). The clock selection is controlled by the

MUX2, MUX1, and MUX0 outputs of the U5 register. The clock is selected

by performing a write to $D0X01 and setting bits 2, 1, and 0 to the

desired values. Table 2-8 shows which clocks are selected by the

different bit settings. The clock source selected for vector driving or

loading is routed from U14-5 to U19 (where it is enabled by DONE- if

vector driving is not complete) and to the SSGATE Flip-Flop U16.

Table 2-9. U6 Register Bit Description (Write @ $D0X11)

___________________________________________________________________________

BIT SIGNAL 1 0

___________________________________________________________________________

7 CLK-POL- Falling Edge Rising Edge

6 ENA-POL Enable High Enabie Low

5 STOP-POL- Falling Edge Rising Edge

4 START-POL- Falling Edge Rising Edge

3 ENA-ALWAYS Enable Always No Enable Always

2 FOR-START- No Forcestart Forcestart

1 STOP-ENA- No Stop Enabled Stop Enabled

0 Unused ---- ----

___________________________________________________________________________

The PSYN signal is inverted by U20 to PSYN-. This allows the vectors to

be driven on the falling edge of PSYN (so the vectors are driven and

settled by the time the rising edge of PSYN clocks the input section.

START/STOP CONTROL

The Start/Stop Control Circuit consists of two 74ACT74 D-Type Flip-Flops

(U13 and U16), a 74AC32 OR Gate (U15), a 74AC20 Quad Input NAND Gate

(U12), and a 74AC08 AND Gate (U19).

U16 determines whether the selected clock source (from U14) decrements

the Vector RAM Address Register (and latches the RAM data out if in the

drive mode) or not. If the DONE- signal is not active on U19-1, the

clock is gated through to U16-3. If the SSGATE- line is high, the clock

is disabled. If SSGATE- is low, the rising-edge of the clock causes

CK-OUT (U16-6) to go high and is presented to the vector drive

circuitry. As soon as the clock input is no longer high, the U15

CLK-PRES output goes low (since U15 pin 5 is low as well) and sets U15,

returning the CK-OUT signal low.

Содержание 9100 Series










































































Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды

Fluke 9100 Series, Руководство по обслуживанию

Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды