Fluke 9100 Series Скачать руководство пользователя страница 40

Страница: 40 / 74

2/Theory of Operation

2-28

step is repeated for the other byte (either the MSB or the LSB).

Finally, another write is made to $D0X21 with bit 2 set that releases

the clear on U28.

When a vector file is driven, on the vector prior to the one designated

by the ENDLOOP statement on the vector file the LOOP output (U601-5)

goes high. This signal is passed from the Top PCA (J5-24) to the Main

PCA (J4-24) and is input to a 74AC00 NAND gate (U19). If the looping is

not complete, LOOP-DONE- is high and passes the signal to the inputs of

two 74HC40103 Counters (U26 and U27), decrementing the counters. This

signal is then fed back as LOOP-LD- to J4-25 and J5-25. It passes

through U7 (Top PCA), clocking the U1 and U2 PE- (parallel load) input,

which loads the LOOP-BACK ADDRESS that is stored in U3 and U4. Each time

the vector that contains the LOOP bit is driven, this process is

repeated until U26 has counted down to zero. The TC- output enables U27

to be decremented by the next LOOP, while U26 is rolled-over, turning

off TC-. This process continues until both counters have reached their

terminal count (which occurs one pass prior to exiting the loop). When

the terminal count is reached, U27 has its LPTC signal go low, providing

a low input to U28 pin 2. Entry into the final LOOP clocks U28 to latch

the data and set LOOP-DONE- low, disabling any further LOOPs from

passing through U19. LOOP-DONE is sent to the Top PCA SSLOGIC Functional

Block for terminating vector driving if the BOTH bit of the Vector

Control RAM is set.

Capture Clock Functional Block

When a vector file is driven with the Capture clock programmed to occur,

the CAP-CLK output at U601-2 goes high for the entire vector period.

CAP-CLK is inverted by U20 and is then “ANDed” with the RAMCLK signal

and output from U20-3. The “ANDing” of the two signals provides the

clocking edge that occurs during the middle of the vector period. The

signal is then passed through the 33 ohm series resistor R10 and passes

from J5-29 to J4-29 of the Main PCA. There the signal is inverted once

more through U19 (Main PCA) before it is routed to the input of the

Clock Mux U18-12 (Main PCA).

Drive Status Functional Block

The Drive Status circuitry is located on the Main PCA. The status of the

Vector Output I/O Module is a 4-bit code returned by performing a read

at $D0X01. Table 2-10 illustrates the significance of the bits returned.

Bit 3 contains the vector drive status (0 - complete, 1 - not complete),

bit 2 contains the HS-ENABLE status (0 - drive suspended for handshake,

1 - drive not suspended for handshake), and bit 1 and bit 0 contain the

module type ID code (Vector I/O = 01). Upon the receipt of RD- on U25-7,

the status of the DONE-signal on U25-16, the HS-ENABLE signal on U25-12,

and the ID code on U25-10 and U25-11 are output on U25-17 through

U25-20. The WR-DLY- signal on U24-1 directs the data through U24 from

the TOPDATA Bus to the A-D-Bus. The address $D0X01 ensures that LATA7-

is low to enable the data. The data is then read by the mainframe

through U8.

Содержание 9100 Series










































































Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды

Fluke 9100 Series, Руководство по обслуживанию

Результаты поиска

Содержание 9100 Series

Отзывы:

Похожие инструкции для 9100 Series

Бренды по названию

Популярные бренды