manualshive.com logo in svg

Fluke 9009, Руководство пользователя

Поделиться
Скачать
Fluke 9009 Скачать руководство пользователя страница 6

9009

User’s Guide

2

Safety Information

General Safety Information is in the printed 

Safety Information

 document that shipped with the Product 

or online at 

www.Flukecal.com

.

 More specific safety information is listed in this manual where 

applicable.
A 

Warning

 identifies conditions and procedures that are dangerous to the user. A 

Caution

 identifies 

conditions and procedures that can cause damage to the Product or the device under test (DUT). 

W

 

Cautions

To avoid possible damage to the Product, follow these guidelines:
•

Never introduce any foreign material into the well.

•

Do not change the values of the calibration constants from the factory set values. The 
correct setting of these parameters is important to the safety and proper operation of 
the Product.

•

Do not slam the probe stems into the well. This type of action can cause a shock to 
the sensor and affect the calibration.

•

Always use a ground fault interrupt device.

•

The Product is a precision instrument. Although it has optimum durability and 
trouble-free operation, it must be handled with care.

•

Most probes have handle temperature limits. Be sure that the probe handle 
temperature limit is not exceeded in the air above the instrument.

•

The instrument and any thermometer probes used with it are sensitive instruments 
that can be easily damaged. Always handle these devices with care. Do not allow 
them to be dropped, struck, stressed, or overheated.

•

Components and heater lifetimes can be shortened by continuous high temperature 
operation.

•

If a mains supply power fluctuation occurs, immediately turn off the Product. Power 
bumps from brown-outs and black-outs can damage the instrument. Wait until the 
power has stabilized before re-energizing the Product.

Contact Fluke Calibration

Fluke Corporation operates worldwide. For local contact information, go to our website: 

www.flukecal.com

To register your product, view, print, or download the latest manual or manual supplement, go to our 
website.
Fluke Corporation

 

P.O. Box 9090

 

Everett, WA 98206-9090

 

+1-425-446-5500

 

[email protected]

Содержание 9009































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды