manualshive.com logo in svg

Fluke 9009, Руководство пользователя

Поделиться
Скачать
Fluke 9009 Скачать руководство пользователя страница 18

9009

User’s Guide

14

Duplex Mode 

The duplex mode can be set to full duplex or half duplex. With full duplex

,

 any commands received by 

the calibrator with the serial interface will be immediately echoed or transmitted back to the device of 
origin. With half duplex

,

 the commands will be executed but not echoed. The duplex mode parameter is 

indicated by,

dUPL

Flashes dUPL and then displays the setting

d=FULL

Current duplex mode setting

The mode may be changed with 

UP

 or 

DOWN

 and 

SET

.

d=HALF

New duplex mode setting

Linefeed

Linefeed enables (on) or disables (off) transmission of a linefeed character (LF, ASCII 10) after 
transmission of any carriage-return. 

LF

Flashes LF and then displays the setting

LF= On 

Current linefeed setting

The mode may be changed with 

UP

 or 

DOWN

 and 

SET

.

LF= OFF

New linefeed setting

Calibration Parameters

The controller gives access to a number of the Product calibration constants: R0, ALPHA, DELTA, and 
BETA (cold side only). These values are set at the factory and should not be altered. The correct 
values are important to the accuracy and proper and safe operation of the Product. Access to these 
parameters is available so that if the controller memory fails

,

 the user may restore these values to the 

factory settings. Keep a list of these constants and their settings with the manual. These constants and 
their settings are on the Report of Calibration that is shipped with the instrument.

W

 Caution 

Do not change the values of the Product calibration constants from the factory

-

set 

values. The correct setting of these parameters is important to the safety and proper 
operation of the Product.

The calibration parameters menu is indicated by:

CAL

Calibration parameters menu

Push 

SET

 five times to enter the menu.

Содержание 9009































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды