Fluke 5730A Скачать руководство пользователя страница 53

Страница: 53 / 104

Multifunction Calibrator

Calibration Check

Calibration Check

Calibration check is similar to the artifact calibration, with the primary difference

being that no changes are made to the stored constants, and the internal check

standards are used as the reference points. A calibration check produces a

report similar to the normal artifact calibration report, and shows any proposed

changes.
This procedure can be done from an external computer, and can be set to run

automatically, with no assistance (there is no need to enter the security

passcode, since no constants are changed).
Use calibration check at any time to confirm the integrity of the Product without

connecting external standards. The calibration check is also useful to collect a

performance history.
Before this procedure is started, make sure the Product is powered on and has

completed the appropriate warm-up period.
To check the calibration:
1. Touch the

Setup Menu

Calibration

to show the Calibration menu.

2. Touch

Run Calibration Check

to begin the procedure.

As the calibration check proceeds, the display shows the current process of

the calibration check. When the check is complete, the largest shift that is

detected is shown on the display. The Product shows when calibration is

complete.

3. Touch

Continue

to return to the Calibration menu. To save the calibration

report, see

Save Calibration Reports

Содержание 5730A









































































































Результаты поиска

Содержание 5730A

Отзывы:

Fluke 5730A, Руководство по калибровке, Страница: 53 / 104

Результаты поиска

Содержание 5730A

Отзывы: