Fluke 5730A Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 104

Fluke 5730A Скачать руководство пользователя страница 47

Multifunction Calibrator

Range Adjustment

37

Range Adjustment

Once artifact calibration is complete, it may be necessary to make further

adjustments to the range. To make a range adjustment, adjust a range constant,

which is an additional gain multiplier. Although range calibration is not needed in

order to meet absolute specifications, they are useful for tuning the Product so

that its values are closer to in-house standards.
Use an in-house laboratory standard to adjust the range constants. The

subsequent procedure for adjusting the range constants is designed for

laboratory standard values that are between 45 % and 95 % of the range’s full-

scale value.
Once the range constant is adjusted, the new constant remains active until the

next calibration, at which time all range constant multipliers are restored to 1. All

range adjustments can be erased by selecting

Restore Factory Defaults

from

the Calibration Menu.
Before the subsequent procedure is started, make sure the equipment necessary

including in-house laboratory standards where necessary, are on hand.
The subsequent example procedure adjusts the 220 V dc range constant with the

listed equipment:

•

732B DC reference standard

•

752A Reference Divider

•

8508A

•

Low Thermal Test Leads: 5730A-7003 (spade lugs)

Note

5440A-7002 and 5440A-7003 Low Thermal Lead sets include a third
cable specifically designed calibrating a Fluke 5440 series
instrument and is not specifically needed here. The 5730A-7002 and
5730A-7003 Low Thermal Lead sets do not include the third cable
for connection between reference standards.

Proceed as follows to adjust the 220 V dc range constant (the procedure is

similar for all ranges). Complete the calibration to external standards before the

range adjustment procedure.

«
...
45
46
47
48
49
...
»

Содержание 5730A









































































































Отзывы:

Нет отзывов