Fluke 5730A Скачать руководство пользователя страница 44

Страница: 44 / 104

5730A

Calibration Manual

Main Output Calibration Procedure

Before this procedure is started, make sure the Product is powered on and has

completed the appropriate warm-up period.
To calibrate the main output functions:
1. Touch

Setup Menu>Calibration

. The calibration menu is shown.

2. If necessary, touch

Temperature

and enter the correct temperature (in

degrees Celsius) to update the ambient temperature. This is the air

temperature in the local vicinity of the Product, which can be seen from

laboratory environmental monitoring devices or from a temperature probe

located closer to the exterior of the Product. Consider the ambient

temperature of the Product if it is located in a rack which can have increased

temperatures.

3. Touch

Run Artifact Cal

to begin the procedure. The Product prompts to refer

to the manual for the correct connections.

4. Connect the 732B to the Product as shown in Figure 1.

Calibrator

732B DC STANDARD

AC P

CAL

CHARGE

BAT

1.01

CHASSIS

GUARD

1.01

COM

SERIAL

UMBER

hhp027.eps

Figure 1. 732B External Calibration Connections

5. Enter the value of the 732B 10 V output. This should be obtained from the

report of calibration for the 732B, and preferably, from control charts that use

linear regression to predict the value of the 732B at the time of use. If the

entered value is not between 9 V and 11 V, an error message is shown.

Restart the process from this point with a calibrated 732B.

6. Push



to start the calibration procedure. As the Product self-

calibrates, it indicates what is happening on the display. When the 6.5 V and

13 V references have been characterized, the display prompts to accept or

reject the changes that are about to be made to the calibration constants.

7. To reject the changes, touch

Cancel

. Otherwise, touch

Continue

to accept

and save the changes, and to continue with calibration.

Содержание 5730A









































































































Результаты поиска

Содержание 5730A

Отзывы:

Fluke 5730A, Руководство по калибровке, Страница: 44 / 104

Результаты поиска

Содержание 5730A

Отзывы: