manualshive.com logo in svg

Fluke 5730A, Руководство по калибровке, Страница: 17 / 104

Поделиться
Скачать
Fluke 5730A Скачать руководство пользователя страница 17

 

Multifunction Calibrator 

 

Electrical Specifications 

7 

 
 
 

Artifact Calibration Standards Requirements 

The following external standards are necessary to calibrate the 5730A to the listed specification. Each external 
standard used must have an uncertainty equal to or less than the listed uncertainty limit. 

Fluke Standard 

Traceable 

Quantity 

Nominal Value  Uncertainty Limit

5730A Specifications Susceptible to 

Uncertainty Limit 

732B 

Voltage 

10 V 

1.5 ppm 

dc volts, ac volts, dc current, ac current 

742A-1 Resistance 

1 

Ω

 

10 ppm 

1 

Ω

, 1.9 

Ω

 

742A-10k Resistance 

10 k

Ω

 

2 ppm 

ac current, dc current 10 

Ω

 to 100 M

Ω

 

Electrical Specifications 

The product specifications describe the Absolute Instrumental Uncertainty of the Product. The product specifications 
include stability, temperature, and humidity; within specified limits, linearity, line and load regulation, and the reference 
standard measurement uncertainty. The product specifications are provided at a 99 %, k=2.58, normally distributed and a 
95 %, k=2, normally distributed level of confidence. Fluke Calibration guarantees product performance to the 99 % level of 
confidence. 
The relative specifications are provided for enhanced accuracy applications.  The specifications apply when range 
constants are adjusted (see "Range Calibration"). To Calculate an enhanced absolute specification from the relative 
accuracy specification, it is necessary to combine the uncertainty of your external standards with the pertinent relative 
specifications. 
Specifications are valid after allowing a warm-up period of 30 minutes, or twice the time the Product has been turned off. 
DC Voltage Specifications 

5730A DC Voltage Specifications 

Range Resolution 

Absolute / 

±

5 

°

C from calibration temperature  

Relative 

±

1 

°

C 

24 Hours 

90 Days 

180 Days 

1 Year 

24 Hours 

90 Days 

±

(ppm  

μ

V) 

99 % Confidence Level 

220 mV 

10 nV 

5 + 0.5 

7 + 0.5 

8 + 0.5 

9 + 0.5 

2 + 0.4 

2.5 + 0.4 

2.2 V 

100 nV 

3.5 + 0.8 

4 + 0.8 

4.5 + 0.8 

6 + 0.8 

2 + 0.8 

2.5 + 0.8 

11 V 

1 

μ

V 

2.5 + 3 

3 + 3 

3.5 + 3 

4 + 3 

1 + 3 

1.5 + 3 

22 V 

1 

μ

V 

2.5 + 5 

3 + 5 

3.5 + 5 

4 + 5 

1 + 5 

1.5 + 5 

220 V 

10 

μ

V 

3.5 + 50 

4 + 50 

5 + 50 

6 + 50 

2 + 50 

2.5 + 50 

1100 V 

100 

μ

V 

5 + 500 

6 + 500 

7 + 500 

8 + 500 

2.5 + 400 

3 + 400 

95 % Confidence Level 

220 mV 

10 nV 

4 + 0.4 

6 + 0.4 

6.5 + 0.4 

7.5 + 0.4 

1.6 + 0.4 

2 + 0.4 

2.2 V 

100 nV 

3 + 0.7 

3.5 + 0.7 

4 + 0.7 

5 + 0.7 

1.6 + 0.7 

2 + 0.7 

11 V 

1 

μ

V 

2 + 2.5 

2.5 + 2.5 

3 + 2.5 

3.5 + 2.5 

0.8 + 2.5 

1.2 + 2.5 

22 V 

1 

μ

V 

2 + 4 

2.5 + 4 

3 + 4 

3.5 + 4 

0.8 + 4 

1.2 + 4 

220 V 

10 

μ

V 

3 + 40 

3.5 + 40 

4 + 40 

5 + 40 

1.6 + 40 

2 + 40 

1100 V 

100 

μ

V 

4 + 400 

4.5 + 400 

6 + 400 

6.5 + 400 

2 + 400 

2.4 + 400 

Notes: 
DC Zeros calibration required every 30 days. 

Содержание 5730A









































































































Отзывы:

Нет отзывов