Fluke 5730A Скачать руководство пользователя страница 32

Страница: 32 / 104

5730A

Calibration Manual

5730A AC Current Specifications: 95 % Confidence Level

Range Resolution

Frequency

(Hz)

Absolute /

C from calibration temperature

Relative

24 Hours

90 Days

180 Days

1 Year

24 Hours

90 Days

(ppm nA)

220

1 nA

10 - 20
20 - 40

40 - 1 k

1 k - 5 k

5 k - 10 k

210 + 16
130 + 10

96 + 8

240 + 12
800 + 65

230 + 16
140 + 10

99 + 8

250 + 12
900 + 65

240 + 16
150 + 10

101 + 8

270 + 12

1000 + 65

250 + 16
160 + 10

103 + 8

280 + 12

1100 + 65

210 + 16
110 + 10

80 + 8

200 + 12
700 + 65

230 + 16
130 + 10

90 + 8

230 + 12
800 + 65

2.2 mA

10 nA

10 - 20
20 - 40

40 - 1 k

1 k - 5 k

5 k - 10 k

210 + 40
130 + 35

96 + 35

170 + 110
800 + 650

230 + 40
140 + 35

99 + 35

180 + 110
900 + 650

240 + 40
150 + 35
101 + 35

190 + 110

1000 + 650

250 + 40
160 + 35
103 + 35

200 + 110

1100 + 650

210 + 40
110 + 35

80 + 35

160 + 110
700 + 650

230 + 40
130 + 35

90 + 35

170 + 110
800 + 650

22 mA

100 nA

10 - 20
20 - 40

40 - 1 k

1 k - 5 k

5 k - 10 k

210 + 400
130 + 350

96 + 350

170 + 550

800 + 5000

230 + 400
140 + 350

99 + 350

180 + 550

900 + 5000

240 + 400
150 + 350
101 + 350
190 + 550

1000 + 5000

250 + 400
160 + 350
103 + 350
200 + 550

1100 + 5000

210 + 400
110 + 350

80 + 350

160 + 550

700 + 5000

230 + 400
130 + 350

90 + 350

170 + 550

800 + 5000

(ppm

220 mA

10 - 20
20 - 40

40 - 1 k

1 k - 5 k

5 k - 10 k

210 + 4

130 + 3.5

96 + 2.5

170 + 3.5

800 + 10

230 + 4

140 + 3.5

99 + 2.5

180 + 3.5

900 + 10

240 + 4

150 + 3.5
101 + 2.5
190 + 3.5

1000 + 10

250 + 4

160 + 3.5
103 + 2.5
200 + 3.5

1100 + 10

210 + 4

110 + 3.5

80 + 2.5

160 + 3.5

700 + 10

230 + 4

130 + 3.5

90 + 2.5

170 + 3.5

800 + 10

2.2 A

20 - 1 k

1 k - 5 k

5 k - 10 k

214 + 35
350 + 80

5000 + 160

224 + 35
390 + 80

6000 + 160

234 + 35
420 + 80

6500 + 160

244 + 35
450 + 80

7000 + 160

200 + 35
300 + 80

5000 + 160

230 + 35
350 + 80

6000 +

160

5725A Amplifier:

11 A

100

40 - 1 k

1 k - 5 k

5 k - 10 k

370 + 170
800 + 380

3000 + 750

400 + 170
850 + 380

3300 + 750

440 + 170
900 + 380

3500 + 750

460 + 170
950 + 380

3600 + 750

300 + 170
700 + 380

2800 + 750

330 + 170

800 + 38

3200 +

750

Note:
Maximum output from the calibrator’s terminals is 2.2 A. Specifications for 220

A and 2.2 mA ranges are increased by 1.3 plus 2

when supplied through 5725A terminals.

Содержание 5730A









































































































Результаты поиска

Содержание 5730A

Отзывы:

Fluke 5730A, Руководство по калибровке, Страница: 32 / 104

Результаты поиска

Содержание 5730A

Отзывы: