Flowserve 6LR-18A, Руководство пользователя

Страница: 31 / 116

APPLICATION
COVERAGE RATES
Dry Mils (Microns) Wet Mils (Microns) Sq Ft/Gal (m²/Gal)
Suggested 4.0 (100) 7.0 (180) 225 (20.9)
Minimum 2.0 (50) 3.5 (90) 450 (41.8)
Maximum 6.0 (150) 10.5 (265) 150 (13.9)
Note: The above reflects the total range to which Series 20 can be applied for specific applications. To insure the proper
thickness and number of coats is specified for certain substrates and exposures, consult the Tnemec Guide Specifications
and/or contact your Tnemec representative. Note: Roller or brush application requires two or more coats to obtain
recommended film thickness. Allow for overspray and surface irregularities. Film thickness is rounded to the nearest 0.5
mil or 5 microns. Application of coating below minimum or above maximum recommended dry film thicknesses may
adversely affect coating performance. †
MIXING
Power mix contents of each container, making sure no pigment remains on the bottom. Pour a measured amount of Part
B into a clean container large enough to hold both components. Add an equal volume of Part A to Part B while under
agitation. Continue agitation until the two components are thoroughly mixed. Do not use mixed material beyond pot life
limits. Note: Both components must be above 50°F (10°C) prior to mixing. For application to surfaces between 50°F to
60°F (10°C to 16°C), allow mixed material to stand thirty (30) minutes and restir before using. For optimum application
properties, blended components should be above 60°F (16°C). Mixing ratio is one (Part A) to one (Part B) by volume.
THINNING
Use No. 4 Thinner. For air spray, thin up to 10% or 3/4 pint (380 mL) per gallon. For airless spray, roller or brush, thin up
to 5% or 1/4 pint (190 mL) per gallon. Caution: Series 20 NSF certification is based on thinning with No. 4 Thinner. Use of
any other thinner voids ANSI/NSF Std. 61 certification.
POT LIFE
20 hours at 50°F (10°C) 10 hours at 77°F (25°C) 4 hours at 100°F (38°C)
APPLICATION EQUIPMENT
Air Spray
Gun Fluid Tip Air Cap Air Hose ID Mat’l Hose ID
Atomizing
Pressure
Pot Pressure
DeVilbiss JGA
E
.070"
765 or 704
5/16” or 3/8”
(7.9 or 9.5 mm)
3/8” or 1/2”
(9.5 or 12.7
mm)
75-100 psi
(5.2-6.9 bar)
10-20 psi
(0.7-1.4 bar)
Low temperatures or longer hoses require higher pot pressure.
Airless Spray
Tip Orifice Atomizing Pressure Mat’l Hose ID Manifold Filter
0.015”-0.019”
(380-485 microns)
1800-3000 psi
(124-207 bar)
1/4” or 3/8”
(6.4 or 9.5 mm)
60 mesh
(250 microns)
Use appropriate tip/atomizing pressure for equipment, applicator technique and weather conditions.
Plural Component Spray: Contact your Tnemec representative or Tnemec Technical Services.
Roller: Roller application optional when environmental restrictions do not allow spraying. Use 3/8” or 1/2” (9.5 mm to
12.7 mm) synthetic woven nap covers.
Brush: Recommended for small areas only. Use high quality natural or synthetic bristle brushes.
SURFACE TEMPERATURE
Minimum 50°F (10°C) Maximum 135°F (57°C)
The surface should be dry and at least 5°F (3°C) above the dew point. Coating won’t cure below minimum surface
temperature.
CLEANUP
Flush and clean all equipment immediately after use with the recommended thinner or MEK.
† Values may vary with color.
© 4/7/2008, by Tnemec Co., Inc.
PRODUCT DATA SHEET
POTA-POX
®
| SERIES 20
WARRANTY & LIMITATION OF SELLER'S LIABILITY: Tnemec Company, Inc. warrants only that its coatings represented herein meet the formulation standards of Tnemec Company, Inc. THE
WARRANTY DESCRIBED IN THE ABOVE PARAGRAPH SHALL BE IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. The
buyer's sole and exclusive remedy against Tnemec Company, Inc. shall be for replacement of the product in the event a defective condition of the product should be found to exist and the
exclusive remedy shall not have failed its essential purpose as long as Tnemec is willing to provide comparable replacement product to the buyer. NO OTHER REMEDY (INCLUDING, BUT NOT
LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR PROPERTY, ENVIRONMENTAL INJURIES OR ANY OTHER INCIDENTAL
OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE TO THE BUYER. Technical and application information herein is provided for the purpose of establishing a general profile of the coating and
proper coating application procedures. Test performance results were obtained in a controlled environment and Tnemec Company makes no claim that these tests or any other tests, accurately
represent all environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection and use of the coating.
Tnemec Company Incorporated 6800 Corporate Drive Kansas City, Missouri 64120-1372 1-800-TNEMEC1 Fax: 1-816-483-3969 www.tnemec.com
PDS20 Page 2 of 2