Chap. 6 Start-up (see fig. 1 pag. 91)
Instructions for a safe pump start
The power cable should have a minimum section equivalent to that of H05 RN-F. To be able to use the pump outdoors,
it is necessary to use cable with a length of 10 m. The plug and connections should be protected by water splashes.
GB
4
Use the pump for the applications listed on the nameplate.
The maximum suction level of 3 mm can be reached in manual mode only. If the level of the fluid to suck is below 20
mm, maximum suction, up to a residual level of 3 meters, can be attained more quickly by starting and topping the
pump 2 or 3 times.
Automatic mode
FLOTEC ComPac
pumps have an integrated floating switch. When the water reaches the start-up level, the
integrated floating switch automatically starts the pump.
When the water falls below the stop level, the integrated floating switch stops the pump.
1. Lower the front lever and place it in location "AUT" (see Fig. 1).
2. Place the pump in a stable and straight position so that the integrated floating switch is able to move freely.
3. To start the pump, insert the plug in a 230 V current socket.
Manual mode
:
The integrated floating switch is disabled so that the pump can run in continuous mode:
1. Lift the front lever and place it in position "MAN" (see Fig. 1).
2. To start the pump, insert the plug in a 230 V current socket.
Overload protection
FLOTEC ComPac
series pumps have a built-in thermal protection switch. The pump stops if an overload condition
occurs. The motor restarts automatically after it has cooled down (see chap 7 of the Troubleshooting section for
information on causes and corrective actions).
In ordinary conditions,
FLOTEC ComPac
series electropumps do not require any maintenance.
It may be necessary to clean the hydraulics or replace the impeller.
Cleaning the hydraulic components
Disassemble the suction filter (Fig. 2 ref. A) by removing the screws provided (Fig. 2 ref. B)
Clean the impeller (Fig. 2 ref. C) and its chamber (Fig. 2 ref. D)
Reassemble the suction filter (Fig. 2 ref. A) by tightening the screws (Fig. 2 ref. B) and making sure that the O-ring
(Fig. 2 ref. E) is correctly positioned in its housing (Fig. 1 ref. E).
Cleaning the floating switch.
Disassemble the suction filter (Fig. 2 ref. A) by removing the screws provided (Fig. 2 ref. B).
Remove the rubber stop (Fig. 2 ref. F) supporting the guide rod (Fig. 2 ref. G)
Remove the floating switch.
Clean the floating switch (Fig. 2 ref. H) and the related chamber (Fig. 2 ref. I).
Insert the floating switch in the guide rod (G) making sure it is inserted in the correct direction (tapered side pointing
upwards).
Insert the rubber stop (Fig. 2 ref. F) on the side of the guide rod.
Reassemble the suction filter (Fig. 2 ref. A) by tightening the screws (Fig. 2 ref. B) and making sure that the O-ring
(Fig. 2 ref. E) is correctly positioned in its housing (Fig. 1 ref. E).
Chap. 7 Maintenance and troubleshooting (see fig. 2 pag. 91)
Pump storage instructions
Store the pump in a dry place and protect it from frost.
Make sure the machine is disconnected from electric power supply, before performing
maintenance operation.
Flotec declines all responsibility for damages originating from an incorrect cleaning. If failures occur, please
contact an authorised Service Center.
GB
9
Содержание COMPAC 150
