FlorCraft 709-3930, Инструкция по эксплуатации, Страница: 5 / 24

– 3 –
Examine extension cord before using
and replace if damaged. Do not abuse
extension cords and do not yank on any
cord to disconnect. Keep cord away from
heat and sharp edges. Always disconnect
the extension cord from the receptacle
before disconnecting the product from the
extension cord.
TO REDUCE THE
RISk OF ELECTROCUTION, kEEP ALL
CONNECTIONS DRY AND OFF THE GROUND.
DO NOT TOUCH PLUG WITH WET HANDS.
• Ground Fault Circuit Interrupter (GFCI)
protection should be provided on the
circuit(s) or outlet(s) to be used for the tile
saw. Receptacles are available having
built-in GFCI protection and may be used
for this measure of safety.
• Use proper extension cord. Make sure your
extension cord is in good condition. When
using an extension cord, be sure to use a
cord heavy enough to carry the current
your product will draw. An undersized cord
will cause a drop in line voltage, resulting
in loss power and overheating. TABLE 1
shows the correct size to use depending
on cord length and nameplate ampere
rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the
heavier the cord.
TO AvOID
PERMANENT MOTOR DAMAGE YOU MUST
USE THE CORRECT ExTENSION CORD.
NEvER USE MORE THAN ONE ExTENSION
CORD AT A TIME.
SPECIFIC SAFETY
INSTRUCTIONS
1. Ensure that the directional arrow marked
on the blade corresponds with the rotational
direction of the motor.
2. With the saw disconnected from the
power supply, rotate the blade by hand to
ensure it is free from obstruction.
3. Always keep the blade-securing arbor and
collars clean.
4. Ensure that the blade-securing bolt is
securely tightened.
5. Never try to cut freehand. Always ensure
that the tile to be cut is pressed firmly
against the rip guide.
6. Ensure the material being cut off has suffi-
cient room to move sideways. Failure to do
so may result in the off-cut binding against
the blade.
7. Never cut more than one tile at a time.
8. Never cut pieces too small that are not
held securely against the rip guide, and
provide enough space for the hand to be a
safe distance from the blade.
9. Ensure that the table and surrounding
area are clear with the exception of the tile
to be cut.
10. Before cutting a tile piece, let the saw
blade run freely for a few seconds. If it
makes an unfamiliar sound or vibrates
excessively, switch it off immediately and
disconnect it from the power supply.
11. Let the blade reach full speed before
beginning the cut.
12. Let the blade come to a complete stop
before removing any jammed material from
around the blade area.
13. Never allow the blade to run dry. Failure
to keep the water tray at the recommended
level will result in possible over-heating of
the diamond blade.
SAW FEATURES
• Removable rear water collection tray
• Adjustable cutting head performs plunge
cuts and 22.5° and 45° bevel cuts
• 10 in. diamond blade cuts tile up to
2-3/8 in. thick
• Maximum rip cut length up to 24 in. tile
— diagonally cuts up to 18 in. tile
• Folding saw stand with wheels offers quick
set up, as well as easy mobility
Ampere rating
Volts Total length of cord in feet
120 V~ 25 ft. 50 ft. 100 ft. 150 ft.
More than No more than AWG
0 6 18 16 16 14
6 10 16 16 14 12
10 12 16 16 14 12
12 16 14 12 Not recommended
TAbLE 1
SPECIFICATIONS
• Motor: 120 Volts~60 Hz,
9.5 Amps, n
0
3450 RPM
• Blade: 10 in. capacity, 5/8 in. arbor
• Assembled Height: 46.25 in.
• Table Area (w/ ext.): 18.5 in. x 22.25 in.
• Weight: 100 lbs (with stand)
UNPACKING
Open carton from the top.
Top tray contents:
• Front extension table
• 10 in. diamond blade
• Upper frame wheels
• Water pump
• Rip guide
• Cord collecting hanger/tool caddy with
blade wrenches (2) and 6 mm Allen key
• Bag of miscellaneous hardware
[includes drain plug, wheel hardware
(2), motor frame mounting screws (3),
hardware for mounting tool caddy (2),
and motor frame locking knob]
• User’s manual
Middle tray contents:
• Saw stand
bottom tray contents:
• Motor head assembly
• Saw frame, including attached table
and water tray
• Rear water collection tray
ASSEMBLY & SET UP
THE FOLLOWING
IS STEP-BY-STEP INSTALLATION AND
OPERATION INSTRUCTION MANUAL.
PLEASE READ THE INFORMATION
THOROUGHLY PRIOR TO USING YOUR
TILE SAW.
A. StAnd Setup
The stand is ready to use. Simply unfold it as
shown in FIGURE 3.
FIGURE 3