48
TRANSLATION OF THE ORIGINAL INSTRUCTIONS (Keep for future reference)
Document Code
Rev.
Date saved
Date printed
T300 - T350 - T400 ISTRUZIONI
01
14/07/2016
14/07/2016
EN
PROBLEM / FAULT
POSSIBLE
CAUSE/S
METHODS AND ANCILLARY NOTES
" #!" \$ $"
workpiece isn't clamped when the pedal
is pressed
- the pedal isn't working;
- main air solenoid valve not working;
j
- the clamping control valve isn't working
- replace the pneumatic pedal; - replace
the solenoid valve or check the electrical
connection;
- check the clamping device's pressure
regulator;
- remove any air leaks; - check/replace
the valves.
" #!" \$ @" $"
two-hand buttons are pressed the
!$$!(!*$'!$+
- the two buttons aren't being pressed
simultaneously;
- the buttons don't work;
- the safety valve of the two-hand control
system is not working;
- air leaks from the system.
- the buttons must be pressed at the same
time;
- check that the buttons work
- check operation of the two-hand control
system safety valve;
- remove any air leaks in the pneumatic
system.
" #!" \$ @" $"
two-hand control buttons are pressed
$"!$$$+%%$!%+%@
- The main cylinder control valve isn't
working properly;
- the cylinder blocking valve isn't working
- air leaks in the pneumatic system;
- check/replace the main cylinder control
valve;
- check the cutting unit up/down piloting
valve pneumatic circuit; - check operation
and opening of the main cylinder lock valve.
- remove any air leaks.
The cut workpiece is full of burrs
- blades aren't sharp;
- central block worn or incorrectly positioned
- sharpen/replace the blades;
- adjust/replace the block
The corners of the assembled frame
#%)$#*%'$#*=$'
" - The cutting angle of the two blades is
^
- the mouldings being cut were not inserted
straight and the base surface is not
level;
- clamping not correctly adjusted
- correct/adjust the blade angle; - replace
the material being cut with mouldings of
better quality;
- check the pressure and position of the
vertical clamping stoppers;
- try using the horizontal clamp.
The corners on the assembled frame are
!%!$\$$"$@%#+[%!$%
are open in the upper section
- verticality of the blades is not correct
- the mouldings being cut were not inserted
straight and the base surface is not
level;
- clamping not correctly adjusted
- correct/adjust blade verticality;
- replace the workpieces with ones of
better quality;
- check the pressure and position of the
vertical clamping stoppers;
""%&$"!$%$="
cut pieces are chipped".
- blades aren't sharp;
- blades are warped;
- vibrations;
- workpiece clamping; - cutting speed
(blade descent); - quality of the material
being cut; - blade not suitable for the
type of material being cut;
- sharpen/replace the blades;
- check/replace the hubs;
- check/replace the belts and check the
drive system; - check the regularity of blade
unit movements;
- check the blade unit balancing system;
- check workpiece clamping;
- adjust the cutting speed (blade descent)
to suit the type of material;
- use a blade type which is suitable for the
material being cut;
- replace the blades;
- check the quality of the workpiece
material;
7. REINSTALLATION
AND
REUSE
CAUTION - DANGER
MOVING AND REINSTALLING THE MACHINE IN A DIFFERENT LOCATION ARE HIGHLY DELICATE OPERATIONS
WHICH CALL FOR SIGNIFICANT EXPERIENCE. CONSEQUENTLY TO ENSURE THAT THE OPERATIONS ARE
CARRIED OUT WITHOUT ANY RISKS FOR PERSONNEL OR THE MACHINE, THESE OPERATIONS MUST BE CARRIED
OUT SOLELY AND EXCLUSIVELY BY PERSONNEL APPOINTED DIRECTLY BY THE MACHINE MANUFACTURER
OR AUTHORISED BY THE SAME.
