background image

3

INSTALLATION, USE AND MAINTENANCE

Fläkt Woods 

 

FIFLO  EN  2014.09   

All rights reserved.

Control System FICO-128

1 Connection instructions, system with individual  
indication

1 Connection instructions, system with  
individual indication

1.1 General

Control unit FCLA-128, communication unit FCBA-2, and 
relay unit FCFA-1 contain electronic components that can be 
damaged if handled incorrectly. Before connecting power, 
all external installations shall be completed.
Control unit FCLA-128, communication unit FCBA-2, and 
relay unit FCFA-1 are mounted with 4 screws located under 
the enclosure cover to ensure protection class IP54.

1.2 Inputs FCLA-128

Supply voltage AC 230 V 2 A, connectors L, N, and PE. Ex-
ample of electric cable type: EKK3G1,5

1.3 Outputs

All relay outputs are potential-free contacts shown in a 
dead state.

ž––Š’˜—ȱŠ•Š›–ȱŒ˜—ŠŒœȱ˜›ȱꛎȱŠ•Š›–ȱǻ–Š›”ŽȱǼȱ’—ȱ

the FCLA-128 are designed for 24 V, 3 A resistive load.
Summation alarm contacts for service alarm (marked SER-
VICE) in the FCLA-128 are designed for 24 V, 3 A resistive 
load.
Relay contacts for interlocking of fans (marked FAN A and 
FAN B) in the FCLA-128 are designed for 230 V, 3 A resis-
tive load. Example of electric cable type: EKK....
If you need more relay contacts for interlocking of fans, the 
system can be expanded with relay unit FCFA-1.

1.4 Damper actuators

Damper actuators are connected to communication unit 
FCBA-2; up to 64 actuators per loop with individual indica-
tion can be connected to the system, but max. two loops per 
communication unit. Control unit FCLA-128 has two loops 
available. For a complete system with 128 damper actuators 
you must use both loops (Link 1 and Link 2).
Supply voltage to actuators 1 and 2 is connected in com-
munication unit FCBA-2 to connectors 1 and 2 (marked 
MOTOR). Indications for closed damper are connected to 
connectors S1 and S2 (marked MOTOR SWITCHES) and in-
dications for open damper to connectors S4 and S6 (marked 
MOTOR SWITCHES).  
S3 and S5 are not used and shall be insulated.

1.5 Smoke detectors

Smoke detectors are connected to communication unit 
FCBA-2; up to 64 smoke detectors per loop with individual 
indication can be connected to the system, but max. two 
loops per communication unit. Control unit FCLA-128 has 
two loops available. For a complete system with 128 smoke 
detectors, you must use both loops (Link 1 and Link 2).
You can choose between three alternative smoke detectors 
Siemens Rököga SOS2... or Calectro UG-3-... or Calectro 
EVC-PY-DA.
When Siemens Rököga SOC2... is used, you can adjust the 
sensitivity of the detector.
If you use Calectro UG-3-... smoke detectors, you must con-

nect the included 2.2 kohm resistor to the smoke detector 
between connectors 1 and 5.
If you use Calectro EVC-PY-DA smoke detectors, you must 
connect the 2.2 kohm resistor to the smoke detector between 
connectors 1 and 3.

1.6 Operating of fans

Control unit FCLA-128 has two relay outputs (two groups) 
for interlocking fans. For more relay outputs / groups, a re-
lay unit FCFA-1 must be connected. Up to eight relay units 
can be connected to the system. (This means up to a total of 
ten relay outputs/groups.)

1.7 Connecting communication to communication 
unit FCBA-2

Control unit FCLA-128 has two connectors for connecting 
communication wires between control unit FCLA-128 and 
communication units FCBA-2 (LINK 1 and LINK 2). Max. 
32 communication units can be connected to each commu-
nication loop.
Note! An individual address should be set for every com-
munication unit (FCBA-2) that shall be connected to the 
control unit (FCLA-128) regardless of whether it is con-
nected to the LINK 1 or LINK 2 or not.
Type of electric cable: 

˜›ȱ˜ĜŒŽȱžœŽȱȬ ȱŘ¡Ř¡Ŗǯś

 

For industrial use ELAKY 2x2x0.6

1.8 Connecting communication to central control 
and monitoring system

Control unit FCLA-128 has connectors for connecting com-
munication wiring (marked MODBUS slave) to a parent 
system for control and monitoring.

1.9 External inputs

There are two inputs for external interlocking:

—™žȱ˜›ȱŽ¡Ž›—Š•ȱꛎȱŠ•Š›–DZȱ—ȱŒŠœŽȱ˜ȱŽ¡Ž›—Š•ȱꛎȱŠ•Š›–ǰȱ

dampers are closed and fan interlocking is activated, possi-

‹’•’¢ȱ˜ȱŠŒ”—˜ •ŽŽȱ ‘Ž—ȱ‘ŽȱŽ¡Ž›—Š•ȱꛎȱŠ•Š›–ȱ‘Šœȱ‹ŽŽ—ȱ

reset. These connectors are normally jumpered, and the 
jumper is removed when this function is connected.
Input for external interlocking: Dampers are closed and fan 
interlocking is activated. Normal status returns when the 
interlocking is removed. 
These connectors are normally jumpered, and the jumper is 
removed when this function is connected.

1.10 Fan groups (zones)

To be able to interlock (stop) the fans in the system, the re-
lays in the control unit FCLA-128 must be activated (Groups 
A and B), with Group A being preselected. If you need more 
groups, you must connect relay units to the control unit, 
which with max. 8 relay units per control unit will allow 10 
relays (groups) for controlling fans. 
All communication units in the system must have a desig-

—ŠŽȱ›˜ž™ȱ’—ȱ˜›Ž›ȱ˜ȱ’—Ž›•˜Œ”ȱŠ—œȱ’—ȱŒŠœŽȱ˜ȱꛎǰȱ˜ȱ’—’

-

cate damper faults, to indicate communication failures, and 
to carry out damper testing.

Содержание FICO FCLA-128

































Отзывы: