background image

Lit. No. 96210/96211, Rev. 00 

3  

June 15, 2008

68595

WARNING

CAUTION

•  DO NOT EXCEED GVWR OR GAWR WITH SPREADER AND LOAD.
•  TURN OFF SPREADER BEFORE FILLING, ADJUSTING, OR CLEANING.
•  BYSTANDERS TO STAY A MINIMUM OF 25 FEET AWAY FROM 

OPERATING SPREADER.

•  DO NOT CLIMB INTO OR RIDE ON SPREADER.
•  KEEP HANDS, FEET, CLOTHING AWAY FROM MOVING CONVEYOR 

AND SPINNER.

•  READ OWNER'S MANUAL AND ENGINE MANUAL BEFORE      

OPERATING OR SERVICING SPREADER.

•  EMPTY AND CLEAN SPREADER AFTER EACH USE.

W65097/F9131

WARNING

Gasoline is flammable.

•  Turn off engine and allow it to cool before filling gas tank.
•  DO NOT smoke or use open flame within 25 feet of spreader.
•  Allow spilled gas to evaporate completely before starting engine.
•  Gasoline engine produces poisonous gases while running.
   DO NOT operate in an enclosed area.
•  Gasoline engine has hot and moving parts that can cause injury. Use care 

when working with or near the gasoline engine and its parts.

•  Shut off engine when not in use, even for short periods of time, to avoid 

damage to equipment or property.

SAFETY INFORMATION

Gasoline Warning 
Label (on Engine 
Cover)

Please become familiar with the Warning 

and Caution labels on the spreader!

NOTE: If labels are missing or cannot be read, see 
your sales outlet.

Warning/Caution Label

Gasoline Warning Label

Warning/Caution Label

Warning/Caution Label

Содержание PRO-CASTER 0806

















Отзывы: