background image

Lit. No. 96210/96211, Rev. 00 

9  

June 15, 2008

Plug Cover

Hook Legs

Spreader

Harness Plug

Vehicle

Harness Plug

WIRING AND HARNESS PLUG INSTRUCTIONS

Wiring Instructions

To properly wire the hopper spreader, please adhere 
to the following recommended installation sequence.

1.  Install either the Spreader or Vehicle Battery Kit 

per the instructions included with the kit.

2.  Install the vehicle harness included with the 

spreader per the following instructions.

3.  Install the cab control per the instructions included 

with the cab control.

Vehicle Harness Installation

All spreaders are shipped from the factory with the 
spreader harness wired to the engine, clutch and 
electric throttle.

NOTE: Use dielectric grease on all electrical 
connections.

1.  Plug the vehicle harness into the spreader 

harness.

2.  Lay out a path for routing the vehicle harness 

into the cab of the truck. Make sure the vehicle 
harness avoids any hot or moving parts of the 
truck. Routing will vary from truck to truck.

3.  Identify a convenient location for the cab control 

that can be reached by the harnesses and wiring.

4.  Drill a 5/8" hole in the 

fi

 re wall so that the vehicle 

harness can reach the desired cab control 
location.

5.  Insert the rubber grommet into the hole.

6.  Route the harness to the desired location.

7.  Secure the vehicle harness to the truck. Verify that 

the harness cannot drop onto the road when it is 
disconnected from the spreader.

Harness Plug and Hook Instructions

1.  Install the plug cover as shown.

2.  Position the legs of the hook over the spreader 

harness.

3.  Twist the hook to spread the wire.

4.  Rotate the hook and push over the spreader 

harness.

5.  Squeeze the legs of the hook together and slide 

the hook over the spreader harness plug.

6.  After connecting the spreader harness plug with 

the vehicle harness plug, secure the plug cover 
into the legs of the hook.

 CAUTION

Before drilling any holes, check both sides 
of the material for any wires, fuel lines, fuel 
tanks, etc. that may be damaged by drilling.

Step 2

Step 3

Step 4

Step 5

Содержание PRO-CASTER 0806

















Отзывы: