background image

Lit. No. 49591, Rev. 05 

11 

July 15, 2020

27775, 28069, 57000, 57000‑1, 57000‑3

VEHICLE LIGHTING CHECK

1. 

Verify the operation of all vehicle front lighting 

prior to connecting the snowplow harness.

2. 

Check the operation of the snowplow lights with 

snowplow mounted to vehicle and all harnesses 

connected.

Turn signals and parking lamps

 

Parking lamps ON:

• 

Both vehicle and snowplow parking lamps 

should be ON at the same time.

 

Driver‑side turn signal ON:

• 

Both vehicle and snowplow driver‑side turn 

signal lamps should flash at the same time.

 

Passenger‑side turn signal ON:

• 

Both vehicle and snowplow passenger‑side 

turn signal lamps should flash at the same time.

Headlamps

 

Move the vehicle headlamp switch to the 

"ON" position. Connecting and disconnecting the 

snowplow lighting harness plug should switch the 

lights between vehicle and snowplow as follows:

 

Snowplow lighting harness DISCONNECTED:

• 

Vehicle headlamps should be ON.

• 

Snowplow headlamps should be OFF.

 

Snowplow lighting harness CONNECTED:

• 

Snowplow headlamps should be ON.

• 

Vehicle headlamps should be OFF.

 

The dimmer switch should toggle headlamps 

between high and low beams. The high beam 

indicator on the dash should light when headlamps 

are placed in high beam.

Daytime Running Lamps (DRLs)

 

An operational check of the vehicle and snowplow 

DRLs will depend on the vehicle model, vehicle 

DRL system, and type of Isolation Module 

installed. Due to the variations in the OEM DRL 

systems and the different Isolation Module 

options available, checking the functionality of the 

snowplow DRLs will depend on the type of module 

installed on the vehicle.

 

With the headlamp switch OFF, activate the 

vehicle DRLs.

 

Snowplow lighting harness DISCONNECTED:

• 

Vehicle DRLs should be ON.

• 

Snowplow headlamps should be OFF.

 

Snowplow lighting harness CONNECTED and 

vehicle in DRL mode:

• 

Check snowplow DRL function per the type of 

Isolation Module installed.

 

Refer to the Mechanic's Guide for information on 

the Isolation Module DRL functions.

Control power indicator light

 

The snowplow plugs 

do

 need to be connected to 

the vehicle harness connectors. The control power 

indicator light should light whenever the control 

ON/OFF switch and the ignition (key) switches are 

both in the "ON" position.

3. 

Connect all snowplow and vehicle harnesses. 

Raise the snowplow and aim the snowplow 

headlamps according to the Snowplow Headlamp 

Beam Aiming Instructions included with the 

headlamps, and any state or local regulations.

4. 

Check the aim of the vehicle headlamps with the 

snowplow removed.

5. 

When the snowplow is removed from the vehicle, 

install plug covers on the vehicle battery cable 

and lighting harness. Insert the snowplow battery 

cable and lighting harness into the cable boot on 

the snowplow.

OWNER'S MANUAL PACKET

If the completed snowplow will be delivered 

immediately, the Owner's Manual should be reviewed 

with and given to the purchaser according to the 

snowplow checklist.

If the snowplow is completed prior to delivery to the 

purchaser, attach the Owner's Manual packet to the 

electrical cable of the cab control for safekeeping.

 CAUTION

On 2‑plug electrical systems, plug covers 

shall be used whenever snowplow is 

disconnected. Vehicle battery cable is 

12V unfused source.

Содержание 27775













Отзывы: