Fisher & Paykel AquaSmart WL37T26KW2 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 79

background image

478182

17

The Softener valve can be tested in diagnostics (refer to Section 6.1.2 for LCD models, or Section
7.2 for LED models).

4.6.4 Inlet

Nozzle

In addition to its design, which ensures excellent rinse water distribution, the nozzle shares an
important relationship with the inlet valve assembly and the dispensing system as described
above.

An internal piston within the nozzle moves with the amount of water pressure against it. When the
water pressure is high, more holes in the nozzle are exposed, and the backpressure on the
dispensing valves is less.

When the pressure is low, more backpressure is created, which ensures that either during
detergent dispensing or bleach dispensing the dispensing system takes priority.

If the water pressure was very low during dispensing, it is conceivable that no water would enter
the machine via the inlet nozzle until the dispensing has been completed.

Conversely, if the piston was jammed and the water pressure was high, a high flow rate of water
would go through the dispensing system and may result in water on the floor.

4.7 Water Level Measurement

The AquaSmart

™

uses the same pressure sensing system used in the EcoSmart

™

and Intuitive

Eco™ machines to determine the water level. The difference with AquaSmart

™

is that on both the

Conventional and High Efficiency modes, AquaSmart

™

will automatically choose the water level,

as the precise water level for the clothes load is critical to the performance of the wash.

The

amount of water used in either mode is unable to be selected or adjusted by the user.

So now there are an infinite number of water levels that AquaSmart

™

can choose depending on

the weight and type of the clothes being washed.

4.8 Motor

4.8.1 Stator

This stator used on the AquaSmart machine is unique to this series only and therefore are not

interchangeable

with any previous phase or series of machines. The stator has 36 poles with

pole tips being curved. The windings are Aluminium and can be Identified by the printed marking

AL 60 190T

it looks the same as the Previous copper Stator but is 19.5

Ω

per winding. The rotor

position sensor is also unique to this stator. (Refer to Section 4.8.3)

Aluminium Stator (36 Poles)

Curved pole tips

«
...
15
16
17
18
19
...
»

Содержание AquaSmart WL37T26KW2
















































































Отзывы:

Нет отзывов

Похожие инструкции для AquaSmart WL37T26KW2

Бренд: Fagor Страницы: 30

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 13

Бренд: Kärcher Страницы: 13

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 15

Бренд: Kärcher Страницы: 20

Бренд: Kärcher Страницы: 112

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 172

Бренд: Generac Power Systems Страницы: 24

Бренд: ZANKER Страницы: 4

Бренд: Belling Страницы: 24

Бренд: Magic Chef Страницы: 32

Бренд: Kärcher Страницы: 180

Бренд: Clarke Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды