Fisher & Paykel AeroCare DE7027G1 Скачать руководство пользователя страница 42

Страница: 42 / 92

Installation instructions

Check that the washer inlet hose (which has been removed from the faucet) has a flat washer or

filter washer fitted. If not insert a flat washer and connect the hose to one of the male couplings
on the “Y” connector.

Take the long inlet hose and insert a flat washer into the straight female coupling and connect it

to the other male coupling on the “Y” connector.

Insert a flat rubber washer into the other female connector and couple the hose to the inlet
valve on the rear of the dryer.

Fig.32 Attaching the inlet hose to the dryer

Check that all connections are firmly hand tight, then using a pair of pliers tighten each coupling

another two-thirds of a turn.

Important!

Ensure you DO NOT OVERTIGHTEN the connections. Overtightening may result in damage to the

couplings.

Fig.33 Tightening the connections

Check immediately for any leaks from the “Y” connector, hose couplings and/or the faucet. Check

again for leaks after 24 hours.

Содержание AeroCare DE7027G1





























































































Результаты поиска

Содержание AeroCare DE7027G1

Отзывы:

Похожие инструкции для AeroCare DE7027G1

Бренды по названию

Популярные бренды

Fisher & Paykel AeroCare DE7027G1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание AeroCare DE7027G1

Отзывы:

Похожие инструкции для AeroCare DE7027G1

Бренды по названию

Популярные бренды