Fisher & Paykel AeroCare DE7027G1 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 92

background image

Installation instructions

25

Connecting an electric dryer (skip for gas dryers) – in Canada only

Electrical requirements (electric models only)

WARNING!

Electric Shock Hazard

Plug appliance into grounded 4 prong outlet.
Failure to do so can result in death or electric shock.

Note: the wiring diagram is located in the control console.

It is your responsibility to:

■

■

Contact a qualified electrical installer.

■

■

Ensure the electrical connection is adequate and conforms with Canadian Electrical Code, C22.1
and all local code requirements.

■

■

Plug the dryer into, or connect the dryer to an individual branch circuit, which is protected by
the correct time delay fuses or circuit breakers. The power supply must be a 4-wire, single phase,
120/240 V, 60Hz, 30 amp circuit.

This dryer is supplied with a CSA approved power cord (5 feet (1.52 m) in length, intended for
plugging into a 14-30R wall outlet. Ensure the outlet is within reach of the dryer’s final location.

4-wire

(NEMA type 14-30R)

A replacement power cord is available, if required. Use of part number 248C1014G001 (240 V
cord set) is recommended. Contact Fisher & Paykel Customer Care (refer to page 86).

Grounding instructions

This dryer MUST be connected to a grounded metal, permanent wiring system.

WARNING!

Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualified electrician or service representative if you are

in doubt as to whether the appliance is properly grounded. Do not modify the plug

provided with the dryer.

«
...
25
26
27
28
29
...
»

Содержание AeroCare DE7027G1





























































































Отзывы:

Нет отзывов

Похожие инструкции для AeroCare DE7027G1

Бренд: NEO TOOLS Страницы: 36

Бренд: Parker Страницы: 106

VORTPHON 2000 P

Бренд: Vortice Страницы: 12

Бренд: Ariston Страницы: 12

Бренд: TEAM CUISINE Страницы: 17

Vital System LG-812

Бренд: Zepter Страницы: 16

Бренд: TEFAL Страницы: 11

Бренд: Podab Страницы: 12

Бренд: Asko Страницы: 32

Бренд: Candy Страницы: 26

Бренд: Candy Страницы: 32

Бренд: Mediclinics Страницы: 40

Бренд: Frigidaire Страницы: 7

FRE5714KW - 5.7 cu. Ft. Electric Dryer

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды