Fisher & Paykel AeroCare DE7027G1 Скачать руководство пользователя страница 40

Страница: 40 / 92

Installation instructions

Adding elbow for exhaust through bottom of cabinet

■

Insert the elbow section of the duct through the rear opening and connect it to the dryer
internal duct.

■

Secure the joint between the internal duct and elbow with duct tape, as shown in Figure 28
(page 37).

Fig.30 Exhaust elbow

■

Complete the exhaust system by connecting the required standard metal elbows and ducts.

■

Cover the original duct opening at the back with a plate (kit WE1M454, available from Fisher &
Paykel (refer to page 86). Refer to Figure 29 (page 37).

■

Move the dryer into its final position.

WARNING!

The rear duct opening must be covered with a plate. The dryer must not be operated

without the plate in place.

Содержание AeroCare DE7027G1





























































































Результаты поиска

Содержание AeroCare DE7027G1

Отзывы:

Похожие инструкции для AeroCare DE7027G1

Бренды по названию

Популярные бренды

Fisher & Paykel AeroCare DE7027G1, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание AeroCare DE7027G1

Отзывы:

Похожие инструкции для AeroCare DE7027G1

Бренды по названию

Популярные бренды