Fisher & Paykel AeroCare DE7027G1 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 92

background image

Installation instructions

14

Connecting a gas dryer (skip for electric dryer)

Refer to page 7 for tools required.

Note: installation and service of this dryer must be performed by a qualified installer, service
agency or the gas supplier.

Gas supply and installation requirements
In the Commonwealth of Massachusetts:

■

■

Installation of the dryer must be completed by a plumber or gas fitter licensed by the state.

■

■

When using ball-type gas shut-off valves, the t-handle type shall be used.

■

■

If using a flexible gas connector, this must not exceed a length of 3 feet in total.

WARNING!

Explosion Hazard

Installations must be performed by a qualified or licensed contractor,

plumber, or gasfitter qualified or licensed by the state, province, or

region where this appliance is being installed.
Use a new AGA or CSA approved gas supply line.
Install a shut-off valve in an accessible place.
Only use a gas shut-off valve approved for use within the state, province,

or region where this appliance is being installed.
Securely tighten all gas connections.
If connecting to LP Gas, have a qualified person make sure gas pressure

does not exceed 13” (330 mm) water column.
Failure to follow these instructions can result in death, explosion, or fire.

«
...
14
15
16
17
18
...
»

Содержание AeroCare DE7027G1





























































































Отзывы:

Нет отзывов

Похожие инструкции для AeroCare DE7027G1

Бренд: PALSON Страницы: 17

Бренд: Gourmia Страницы: 20

Zander WVM 1080

Бренд: Parker Страницы: 56

Бренд: Morris Страницы: 4

SilverLine SLE40

Бренд: Anetsberger Brothers Страницы: 2

Бренд: Kalorik Страницы: 24

Бренд: Smeg Страницы: 32

Бренд: Kalorik Страницы: 40

Бренд: Maytag Страницы: 20

Бренд: Tricity Bendix Страницы: 12

Бренд: Tricity Bendix Страницы: 13

Бренд: Monzana Страницы: 18

Бренд: Siemens Страницы: 44

Бренд: Siemens Страницы: 40

Бренд: Siemens Страницы: 48

Бренд: Siemens Страницы: 48

Бренд: Siemens Страницы: 32

Бренд: Siemens Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды