Fisher & Paykel AeroCare DE7027G1 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 92

background image

Installation instructions

35

Dryer exhaust to right, left or bottom of cabinet

WARNING!

Before performing this exhaust installation, be sure to disconnect the dryer from its

electrical supply. Protect your hands and arms from sharp edges when working inside

the cabinet. Be sure to wear gloves.

Important!

■

■

Dryer exhaust to right of cabinet (electric models only).

■

■

Dryer exhaust to left of cabinet (gas and electric models).

Detach and remove the bottom, right or left side knockout (the opening for alternate ducting),
as preferred for the direction of ducting. Tape around the knockout and exhaust opening to
provide protection from sharp edges during installation. Remove the screw inside the dryer
exhaust duct and slide the duct out of the dryer. Keep the screw. Cut the duct as shown in
Figure 24. Retain portion A of the duct.

Right (electric
models only)

Fig.24 Removing and
shortening the duct

Remove desired
knockout (one only)

Remove screw
and save

Bottom (gas
and electric
models)

Left (gas and
electric models)

Fixing hole

9” (230 mm)

Tab location

Through the rear opening, find the tab located in the middle of the dryer base. Using a flat blade
screwdriver, lift the tab to approximately 45°.

Bend tab
up 45°

Fig.25 Lifting the tab

«
...
35
36
37
38
39
...
»

Содержание AeroCare DE7027G1





























































































Отзывы:

Нет отзывов

Похожие инструкции для AeroCare DE7027G1

Бренд: Ga.Ma Страницы: 38

Frialator SF14 UFM

Бренд: Pitco Страницы: 43

Бренд: Heinner Страницы: 72

Бренд: Zephir Страницы: 4

Бренд: T-Fal Страницы: 21

Бренд: Maytag Страницы: 17

Бренд: Frymaster Страницы: 37

Бренд: Optimum Страницы: 45

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 18

Бренд: Frigidaire Страницы: 14

Бренд: Frigidaire Страницы: 21

Бренд: Frigidaire Страницы: 18

Бренд: Frigidaire Страницы: 24

Бренд: Frigidaire Страницы: 18

Бренд: Frigidaire Страницы: 36

Бренд: Frigidaire Страницы: 52

Бренд: Frigidaire Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды