background image

Page  46

Troubleshooting

Error

Possible Cause

Solutions

System is not receiving 
power or is not powering up

Cable from power adapter is loose or is unplugged

•  Confirm that all cables are connected correctly
•  Confirm that the power adapter is securely connected to the back 

of the unit

Cables are connected, but system is not receiving 
sufficient power

•  Confirm that the system is powered on (LED indicators on the 

front should be ON)

•  If the unit is connected through a power bar or surge protector, 

try bypassing the bar and connecting the power directly to the 
wall outlet

•  Confirm that there is power at the outlet

•  Connect the power cable to another outlet
•  Test the outlet with another plugged device

Remote control not detected 
by the system

Battery in the remote control is drained or is missing

•  Install two fresh AAA alkaline batteries in the remote control

Hard drive is not detected by 
the system

Hard Drive is not formatted

•  Format the hard drive per instructions

Hard drive cables are loose or not properly connected

•  Remove the housing and check that hard drive cables are firmly 

connected

There is no hard drive in the system

•  Open the housing and install a 3.5 SATA hard drive

Hard drive is full (0% 
remaining) and the unit is no 
longer recording

Overwrite is not enabled

•  From the Main Menu, select HDD>Overwrite>Enable and click 

Apply

Mouse is not detected by 
system

Mouse cable is not connected or is not firmly 
connected to the system

•  Firmly connect the mouse cable to the USB Mouse port (not the 

USB Data port) on the front panel.

System needs to be reset

•  Power off the system (Turn power switch off position on back 

of unit). Firmly connect a USB mouse to the USB Mouse port on 
the front panel of the system. Power on the system (Turn power 
switch to on position on back of unit).  

There is no picture on 
selected channels/camera 
picture is not being 
displayed

Camera cables are loose or have become 
disconnected

•  Check the camera video cable and connections
•  Disconnect and reconnect the cable at the system and at the 

camera

•  Try moving the camera to another channel or use another cable

The image on the DVR 
appears but does not have 
sound

Audio cables are loose or have been disconnected

•  Check the AUDIO connections to the DVR

Audio channels are disabled the system menu

•  Check the Configurations: Main Menu>Record>Audio

Volume on external speakers (not included) is low or 
off

•  Increase volume on external speakers (not included)

Cameras are not audio capable or a powered 
microphone is not attached

•  Add audio capable cameras or a powered microphone (not 

included with this kit)

The system beeps at startup

The beep at startup is normal

•  No action required

I am not receiving e-mail 
notifications

E-mail notification is disabled

•  Open Main Menu>Advance>Alarm; click E-MAIL SETUP; under 

E-MAIL select ON

Default setting is disabled and /or you have not 
entered your own SMTP information

•  If you want to use your own SMTP server, deselect the Default 

box, and enter your SMTP Server Address, Port, User name, and 
Password in their respective fields

Appendix

Troubleshooting

Содержание PRO-DC8410-600

















































Отзывы: