First Alert FA148CP Series, Инструкция по установке и настройке

Страница: 36 / 96

*98
Command to Exit Program Mode
(with installer code lockout)
Exits Programming Mode and prevents re-entry by:
Installer Code + [8] + [0] + [0]. To enter the programming
mode if
∗
98 was used to exit, you must first power the system
down. Then power up again, and press [
∗
] and [#] at the same
time, within 50 seconds of powering up.
See field *88 for other Program mode lockout options.
*99
Command to Exit Program Mode Exits Programming Mode and allows re-entry by:
Installer Code + [ 8] + [0] + [0] or by: Pressing [
∗
] and [#] at
the same time, within 50 seconds of power-up.
Pager Programming Fields
FIELD TITLE and DATA ENTRIES EXPLANATION
*160
Pager 1 Phone No.
Enter up to 20 digits
If you enter fewer than 20 digits, exit by pressing [
∗
] and next field
number. To clear entries from this field, press
∗
160
∗
.
*161
Pager 1 Characters
Enter up to 16 characters
Up to 16 optional characters may be sent as a prefix to the 7-digit
system status code sent to pager #1 (if used). Phone number in field
*160 must have been entered. If fewer than 16 characters, exit by
pressing [
∗
] and next field number. To clear entries from this field,
press
∗
161
∗
.
For example, these optional 16 characters may be composed of the
following:
•
PIN number (to identify a specific pager to the paging company)
•
Subscriber account number
•
∗
(enter # + 11 to send
∗
)
•
# (enter # + 12 to send #)
•
Pause (enter # + 13 to allow a 2-second pause)*
•
Any special character(s) the end user may decide to transmit
* Some paging systems require pause(s) before the prefix.
The format for the 7-digit system status code is defined as follows:
Pager Format: XXX-YYYY where:
XXX
= 3-digit event code: 911 = Alarm
811 = Trouble
101 = Opening (disarm)
102 = Closing (arm AWAY)
YYYY = 4-digit user or zone number (depending on type of event).
The first digit indicates partition (0 = system, 1 = part 1,
2 = part 2, 3 = common), followed by the 3-digit user or
zone number.
Example 1. Pager displays: 9 1 1 – 1 0 0 4
This indicates that the system is reporting an alarm (911) caused by
a fault in zone 4 (0004) in partition 1.
Example 2. Pager displays:
1 0 2 – 2 0 0 5
This indicates that the system is reporting a closing–system arming
(102) by User 5 (0005) in partition 2.
*162
Pager 1 Report Options
0 = No reports sent
1 = Open/close for all users enabled to page
†
4 = All alarms and troubles
5 = All alarms, troubles, and open/close for
all users enabled to page
12 = Alarms and troubles for zones entered
in zone list 9
13 = Alarms and troubles for zones listed in
zone list 9 and open/close for all users
enabled to page
Enter the types of reports to be sent to pager 1 for each partition.
† Reports to pager only when arming (close)/disarming (open) from a
keypad using a security code; auto-arming/disarming, arming with
assigned button, and keyswitch arming do not send pager messages.
*163
Pager 2 Phone No.
Enter up to 20 digits
If you enter fewer than 20 digits, exit by pressing [
∗
] and next field
number. To clear entries from this field, press
∗
163
∗
.
Installation Instructions
4-10