background image

I

NSTALLATION 

(C

ONTINUED

)

P

AGE 

5

Fireplace Placement Requirements

Minimum Framing Dimensions

45-1/2"

We recommend installing the 
shaded framing members 
after installing the chimney.  
Arrange the framing 
members so there is not a 
vertical member directly in 
the center of the opening 
where it would interfere with 
pipe clearances.

26"

43"

Header
(install veritcally to 
ensure proper pipe to 
header clearance) 

A firestop is required at the top of 
the fireplace enclosure or ceiling 
level (whichever is lower).

Min. 4-1/2"

NOTE: make sure the 
enclosure is wide enough to 
accommodate the blower 
(see the section"Blower" for 
details).

The fireplace enclosure must not be 
less than 81" above the base of the 
fireplace.  
• If the fireplace is raised, the 

enclosure height must be raised to 
maintain the 81".

• Do not build into this area.  
• Do not slope the walls inward.  
• The header, vertical framing 

members, and all interior wall 
surfaces may protrude a maximum 
4" into this area.

The fireplace uses 1/2" standoffs on the back and sides and 4" stand-offs on the top to space the
fireplace away from framing members or walls.  These stand-offs may contact the framing members or
walls but do not place insulation or other material in the space between the stand-offs and fireplace.

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AAA

AAA

AAA

AAA

AAA

AAA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

AA

Travis Industries 
recommends the chase 
around the fireplace be 
insulated.  This insulation 
should only be placed 
between the framing 
members and secured so 
it does not fill the space 
between the fireplace and
standoffs.

Bend this bracket down 
on each side and nail it 
to the floor, securing the 
fireplace in position.

These lifting handles are 
removed (use a 7/16" wrench) 
once the fireplace is in place.

Standoffs (also 
located on back)

The fireplace (and 
firebox) must be made 
level and plumb during 
installation.  Use shims 
under the fireplace to 
properly level the 
fireplace.  

Zero 

Clearance 

Can

Firebox

WARNING:
Failure to correctly level and plumb 
this fireplace will lead to doors that 
swing open or closed.

AAA

AAA

AAA

AAA

AAA

AAA

AAA

The fireplace must be secured to the floor (use the lifting handle brackets - see illustration above).

Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)

Содержание 36 ELITE-ZC

























Отзывы: