manualshive.com logo in svg
background image

EPA Wood-Burning Fireplace

P/N  900089-00  REV. NC  12/2013

WCT6840WS

MODEL

WCT6840WS

This installation manual will enable you to obtain a safe, efficient and 

dependable installation of your fireplace system. Please read and 

understand these instructions before beginning your installation.

Do not alter or modify the fireplace or its components under any circum-

stances.  Any modification or alteration of the fireplace system, including 

but not limited to the fireplace, chimney components and accessories, 

may void the warranty, listings and approvals of this system and could 

result in an unsafe and potentially dangerous installation.

IHP wood-burning fireplaces are designed for use as a supplemental 

heater.   They are not intended for continuous use as a primary heat 

source.

INSTALLATION AND 

OPERATION INSTRUCTIONS

SAVE THESE INSTRUCTIONS

FOR FUTURE REFERENCE

Listed to standards:
ULC-S610 and UL-127
Report No. 304-7213
EPA Cert. No. 609

     

WARNING

 

Hot! Do not touch!  The glass and 

surfaces of this appliance will be hot 

during operation and will retain heat 

for a while after shutting off the appli-

ance.  Severe burns may result. 

• 

 

Carefully supervise children in the 

same room as appliance.

 

If small children are present in the home, it is 

recommended that this appliance be fitted with 

an adjustable safety gate or barrier screen.

       WARNING

•  The fireplace cannot be operated without a door 

or firescreen.  Consult your dealer to select the 

correct replacement door or firescreen.

•  The fireplace is equipped with a blower, electri-

cal connection must be made prior to fireplace 

installation

•  Important! To assure proper alignment of glass 

doors:  Install  this  fireplace  in  a  square  and 

plumb condition, using shims as necessary at 

sides and/or bottom.

•  Install the fireplace only as described in these 

instructions.

An French manual is available upon request. Order P/N 900090-00.
Ce manuel est disponible en francais, simplement en faire la demande. 
Numéro de la pièce 900090-00.

12

/18

/20

13

Содержание WCT6840WS



























Отзывы: