Fire-Lite Alarms MS-4412B Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 52

background image

MS-4412B/MS-4424B Instruction Manual PN 15125:G1 10/22/02

37

Appendix B: NFPA Standard-Specific Requirements

Minimum System Requirements

The control panel has been designed for use in commercial, industrial, and institutional applications and
meets the requirements for service under the National Fire Protection Association (NFPA) Standards
outlined in this appendix. The minimum system components required for compliance with the appropriate
NFPA standard are listed below.

•

Fire Alarm Control Panel.

Contains the main control board, cabinet (backbox and door), main

supply transformer and power supply.

•

Batteries.

Refer to "Appendix A: Secondary Power Calculations" on page 35.

•

Initiating Devices.

Connected to one of the control panel's Initiating Device Circuits.

•

Notification Appliances.

Connected to one of the control panel's Notification Appliance Circuits.

Additional Requirements

The following additional equipment is needed for compliance with the NFPA standards listed below. The
relay contacts of this control panel may be used to trip any dialer that is UL listed for Central Station/Remote
Station services. The illustrations in this appendix provide examples of possible system configurations.

Note:

Applications which require the the NOTI-FIRE 911AC or the Potter EFT-C are not FM approved.

NFPA 72 - Signaling Systems for Central Station Service (Protected Premises Unit)

•

NOTI-FIRE 911AC Digital Alarm Communicator/Transmitter

connected to a compatible

listed Central Station DACR or Protected Premises Receiving Unit. See "Digital Alarm
Communicator/Transmitter - Noti-Fire 911AC" on page 38 for installation instructions for this unit.

•

411UDAC Universal Digital Alarm Communicator

connected to a compatible listed Central

Station DACR or Protected Premises Receiving Unit. See "Universal Digital Alarm Communicator
- 411UDAC" on page 39 for installation instructions for this unit.

NFPA 72 - Auxiliary Fire Alarm System

•

4XTMF (4412TM) Transmitter Module

for connection to a compatible listed Local Energy

Municipal Box. See "Local Energy Municipal Box" on page 40 for installation instructions for this
unit.

NFPA 72 - Remote Station Fire Alarm System

•

Fire•Lite RS82-9 Remote Station Receiver

connected to a 4XTMF (4412TM) Transmitter

Module. See "Remote Station Receiver - RS82-9" on page 41 for installation instructions for this
unit.

•

NOTI-FIRE 911AC Digital Alarm Communicator/Transmitter

connected to a compatible

listed Central Station DACR. See "Digital Alarm Communicator/Transmitter - Noti-Fire 911AC"
on page 38 for installation instructions for this unit.

•

411UDAC Universal Digital Alarm Communicator

connected to a compatible listed Central

Station DACR. See "Universal Digital Alarm Communicator - 411UDAC" on page 39 for
installation instructions for this unit.

NFPA 72 - Proprietary Fire Alarm System

•

Potter EFT-C McCulloh Transmitter

. See "Potter EFT-C McCulloh Transmitter" on page 42 for

installation instructions for this unit.

«
...
35
36
37
38
39
...
»

Содержание MS-4412B





















































Отзывы:

Нет отзывов

Похожие инструкции для MS-4412B

Бренд: jbc Страницы: 4

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Farfisa Страницы: 20

Бренд: Racal Instruments Страницы: 64

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренд: Z-Wave.Me Страницы: 4

Extra Free RZB-02

Бренд: Zamel Страницы: 2

Бренд: Yamaha Страницы: 2

Бренд: Full Gauge Controls Страницы: 3

Бренд: Miller-Leaman Страницы: 18

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

eTracer ET4415BND

Бренд: Epsolar Страницы: 44

Бренд: Graco Страницы: 166

Бренд: Automated Logic Страницы: 10

Бренд: Argo-Hytos Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды