Fire-Lite Alarms MS-4412B Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 52

background image

3. System Operation

Control Switches

30

MS-4412B/MS-4424B Instruction Manual PN 15125:G1 10/22/02

Control Switches

Figure 21 Control Panel Switches

Tone Silence -

Pressing this switch acknowledges alarms, troubles and supervisories. The panel has

alarm and trouble resound with LED flash of new conditions. The flashing trouble LED(s) illuminate
steadily and the piezo turns off. A second trouble will resound the piezo. Trouble conditions are self-
restoring. Alarms latch and require pressing SYSTEM RESET to clear. Unless the unit is set for non-
latching supervisory service, supervisories latch and require pressing SYSTEM RESET to clear. The piezo
has three tones for different conditions (see "Piezo" on page 31).

Alarm Silence -

Pressing this switch acknowledges for alarms and supervisories. This switch will

silence the local piezo, change any flashing alarm LEDs to steady, and turn off the notification circuits.
The “Alarm Silenced” LED will illuminate. Alarm silence is a latching function and requires pressing
SYSTEM RESET to clear.

Note:

If Silence Inhibit has been selected (SW1, DIP switch #4 set to “ON”), the Alarm Silence will not function until 60

seconds after the initiation of the alarm.

Alarm Activate -

This switch may be used to activate Notification Appliance Circuits (NACs). It also

activates the System Alarm Relay. This is a latching function. Pressing ALARM SILENCE silences the
NACs and System Alarm Relay, and lights the Alarm Silenced LED. Pressing SYSTEM RESET returns
the system to normal.

System Reset -

This switch breaks power to all initiating circuits, four-wire smoke detector power and

optional boards and will clear any activated output circuits. If any alarm or trouble still exists after reset,
they will reactivate the panel. Holding SYSTEM RESET down will perform a LAMP TEST function and
will activate the piezo sounder.

Zone Status LEDs

The alarm and/or trouble LED(s) will flash until the event(s) has been acknowledged (TONE or ALARM
SILENCE), at which point the LED(s) will illuminate steadily.

Figure 22 Zone Status LEDs

TONE

SILENCE

ALARM

SILENCE

ALARM

ACTIVATE

SYSTEM

RESET

M

S

44

-p

an

el

2.

cdr

ZONE 1

ZONE 2

ZONE 3

ZONE 4

MS

44

-p

an

el

3.

cd

r

Alarm LED

Trouble LED

«
...
28
29
30
31
32
...
»

Содержание MS-4412B





















































Отзывы:

Нет отзывов

Похожие инструкции для MS-4412B

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Samson Страницы: 100

Бренд: Radio Shack Страницы: 3

Бренд: Rain Bird Страницы: 48

Бренд: Access Страницы: 12

Бренд: Baader Planetarium Страницы: 7

Бренд: Beaphar Страницы: 2

Бренд: Danfoss Страницы: 32

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 44

PVG 16 PVH/Covers

Бренд: Danfoss Страницы: 144

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 64

Бренд: Danfoss Страницы: 8

VLT AutomationDrive FC 360

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 6

Бренд: Danfoss Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды