Fiery E-41 Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 161

background image

S

YSTEM

AND

USER

SOFTWARE

108

N

OTE

:

This installation segment takes approximately 12 minutes.

8. At the message “System Software is copied to the system. Remove media and select OK to

reboot,” remove the System Software DVD, and then select OK.

The E-41 reboots several times and status messages display as the installation process
continues.

N

OTE

:

This installation segment takes approximately 12 minutes.

9. At the message “Please insert User Software to continue installation,” insert the User

Software DVD into the DVD/CD-RW drive.

N

OTE

:

If a monitor is connected (FACI), click OK to continue.

During this process, the following installations are performed:

• The entire contents of the System Software DVD are copied to a shared folder on the E-41

HDD, in e:\efi\user_sw.

After installation, when the E-41 is connected to the customer’s network, users can access
the user software in the shared folder and install it onto client computers.

The message “Copying User Software to Fiery shared folder. Please wait” and other messages
display describing the user software installation process.

N

OTE

:

This installation segment takes approximately 30 minutes.

10. At the message “Setup finished. Remove CD/DVD. Press OK to reboot,” remove the User

Software DVD and select OK.

If the User Software DVD does not eject automatically, wait for the system to boot completely
and the following logo screen to display on the E-41 Control Panel, then access the Functions
menu on the E-41 Control Panel and select Eject CD/DVD to remove the User Software
DVD.

N

OTE

:

This installation segment takes approximately 5 minutes.

This logo screen indicates that the E-41 is Idle.

Server name

«
...
106
107
108
109
110
...
»

Содержание E-41


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E-41

Бренд: H3C Страницы: 57

Бренд: K&K Страницы: 6

Бренд: 2gig Technologies Страницы: 4

Бренд: 2gig Technologies Страницы: 2

Бренд: G1SLE Страницы: 2

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

C-NaviGator III

Бренд: C-Nav Страницы: 20

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 95

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 33

Бренд: Danfoss Страницы: 59

Бренд: Danfoss Страницы: 16

VLT AQUA Drive FC 200

Бренд: Danfoss Страницы: 91

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 100

Бренд: Danfoss Страницы: 82

Бренд: Danfoss Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды