Festo EMCS-ST Скачать руководство пользователя

Страница: 59 / 86

Maintenance and care

If used as intended, the product is maintenance-free.
•

Clean the outside of the product with a soft cloth.

Diagnostics and malfunctions

13.1

Diagnostics via LED displays

13.1.1

LED "C/Q" (communication and device status)

LED

Meaning

Off

–

no logic voltage

–

Control interface "digital inputs/outputs (DIO) or IO-Link (LK) [Logic]" not
active

green light

–

Control interface "digital inputs/outputs (DIO) [Logic]" active, drive ready
for DIO operation
(communication between controller and EMCS-ST possible)

flashing green

–

Control interface "IO-Link (LK) [Logic]" active
(communication between IO-Link master and EMCS-ST possible)

yellow light

–

Warning active or system not referenced
(The warning can be read out via the IO-Link interface)

red light

–

Error active
(Errors are displayed via the LED displays menu and parameters or can be
read out via the IO-Link interface)

Tab. 27 LED "C/Q" (communication and device status)

Maintenance and care

Festo — EMCS-ST — 2020-04a

Содержание EMCS-ST






















































































Результаты поиска

Содержание EMCS-ST

Отзывы:

Похожие инструкции для EMCS-ST

Бренды по названию

Популярные бренды

Festo EMCS-ST, Руководство по эксплуатации

Результаты поиска

Содержание EMCS-ST

Отзывы:

Похожие инструкции для EMCS-ST

Бренды по названию

Популярные бренды