manualshive.com logo in svg

Festo EMCS-ST, Руководство по эксплуатации

Поделиться
Скачать
Festo EMCS-ST Скачать руководство пользователя страница 39

11.2.6

Master control

Function

The master control specifies which interface has the authorisation to control the EMCS-ST.
During operation, only one of the following interfaces can be the master control:
–

digital inputs/outputs (DIO) [Logic]

–

IO-Link (LK) [Logic]

–

Display and operating component (HMI)

The display and operating component (HMI) always has higher priority than the control interface
"digital inputs/outputs (DIO)" or "IO-Link (LK)" [Logic].
If the pushbutton actuator lock is released, incoming travel commands are blocked and not executed.

"Digital inputs/outputs (DIO)" or "IO-Link (LK)" master control

After switching on the power supplies and initialising the EMCS-ST, the master control is automatically
assigned to the "digital inputs/outputs (DIO)" control interface. The detection of an active IO-Link
master causes the master control to switch automatically to the "IO-Link" control interface. If the IO-
Link communication is interrupted, the master control automatically returns to the "digital inputs/out-
puts (DIO)" control interface.

Timing

The diagrams show the automatic transfer of the master control between the "digital inputs/outputs
(DIO)" and "IO-Link (LK)" [Logic] control interfaces.

1 IO-Link master active "control interface

[Logic]" 

2 Master control "DIO"

3 Master control "IO-Link"
4 LED C/Q (system referenced)
5 LED C/Q (system not referenced)

Fig. 16 "Digital inputs/outputs (DIO)" or "IO-Link (LK)" master control

Drive system

39

Festo — EMCS-ST — 2020-04a

Содержание EMCS-ST























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды