Ferris CCW36 Series Скачать руководство пользователя страница 31

Страница: 31 / 52

Figure 23. Tightening the Mower Blade for Installation
A. Mower Blade Mounting Bolt
B. Flat Washer
C. Mower Blade Air Lift (Points Up For Installation)
D. 4 X 4 Wooden Block

Sharpening the Mower Blade

1. Sharpen the mower blades with grinder, hand file, or

electric blade sharpener.

2. Sharpen the mower blade by removing an equal amount

of material from each end of the mower blade.

3. Keep the original bevel (

A, Figure 21

) when grinding.

DO NOT change the mower blade bevel.

4. The mower blade should have a maximum 1/64” (0,40

mm) cutting edge (

) or less.

5. Balance the mower blades before installing.

Balancing the Mower Blades

1. Clean the mower blade to remove any dried grass or

other debris.

2. See Figure 22. Put the mower blade on a nail in a vise

and turn the mower blade to the horizontal position.

3. Check the balance of the mower blade. If either end of

the mower blade moves downward, sharpen the heavy
end until the mower blade is balanced.

See Sharpening

the Mower Blades

for proper sharpening instructions.

4. Repeat the process until the mower blade remains in the

horizontal position.

Reinstalling the Mower Blades

1. Reinstall each mower blade with the air lifts pointing up

towards the mower deck as shown in Figure 23. Secure
with the mower blade mounting bolt and flat washer (

& B, Figure 23

2. Wedge a wooden block between the mower blade and

the mower deck housing to keep the mower blade from
turning and torque the mower blade mounting bolt to 70
lbs-ft (94 Nm).

Figure 21. Sharpening the Mower Blade
A. Mower Blade Bevel
B. Mower Blade Cutting Edge

Figure 22. Balancing the Mower Blade
A. Nail

CAUTION

Avoid injury! Keep mower blades
balanced.

An unbalanced mower blade can create excessive vibration
and damage the unit or cause mower blade failure.

CAUTION

Avoid injury! Mower blades are sharp.

• Always wear gloves when handling mower blades or

working near blades.

• Always wear safety eye protection when grinding.

Regular Maintenance

Not

for

Reproduction

Содержание CCW36 Series





















































Результаты поиска

Содержание CCW36 Series

Отзывы:

Похожие инструкции для CCW36 Series

Бренды по названию

Популярные бренды

Ferris CCW36 Series, Руководство оператора

Результаты поиска

Содержание CCW36 Series

Отзывы:

Похожие инструкции для CCW36 Series

Бренды по названию

Популярные бренды