background image

10

www.ferrisindustries.com

Operator Safety

Safety Interlock System

This unit is equipped with safety interlock switches.  These 
safety systems are present for your safety, do not attempt 
to bypass safety switches, and never tamper with safety 
devices.  Check their operation regularly.

Operational SAFETY Checks

Test 1 — Engine should NOT crank if:

  •  PTO switch is engaged, OR

  •  Parking brake is not engaged, OR

  •  Forward speed control lever is not in the NEUTRAL 

position.

Test 2 — Engine SHOULD crank if:

  •  PTO switch is NOT engaged, AND

  •  Parking brake is engaged, AND

  •  Forward speed control lever is in the NEUTRAL position.

Test 3 — Engine should SHUT OFF if:

  •  Operator releases the operator presence handles with 

the PTO engaged OR

  •  Operator releases the operator presence handles with 

the parking brake disengaged.

Test 4 — Blade Brake Check

Mower blades and mower drive belt should come to a 
complete stop within seven (7) seconds after electric PTO 
switch is turned off (or operator releases the operator 
presence handles).  If mower drive belt does not stop within 
seven (7) seconds, see your dealer.

NOTE: Once the engine has stopped, PTO switch must be 
turned off, parking brake must be engaged, the forward 
speed control lever must be locked in the NEUTRAL 
position, and the operator must engage the operator 
presence handles in order to start the engine.

Safety Icons

The alert symbol (

) is used to identity safety information 

about hazards that can result in personal injury.  A signal 
word (DANGER, WARNING, or CAUTION) is used with the 
alert symbol to indicate the likelihood and the potential 
severity of the injury.  In addition, a hazard icon may be 
used to represent the type of hazard.  An explanation of 
hazard levels and icons are as follows:

North American Safety Icons

Alert

Toxic Fumes

Read the 

Manual

Open Flame 

Hazard

Fire Hazard

Amputation - 

Rotating Parts

Amputation - 

Hand In Blade

Amputation - 
Foot In Blade

Thrown Objects

Hot Surface

Wear Protective 

Gear

Pinch Point

Kickback

Remove 

Key Before 

Servicing

WARNING

If the unit does not pass a safety test, do NOT operate 
it.  See your authorized dealer.  Under no circumstance 
should you attempt to defeat the purpose of the safety 
interlock system. 

DANGER

This indicates a hazard which, if not avoided, 

will result in 

serious injury or death.

 

WARNING

This indicates a hazard which, if not avoided, 

could result 

in serious injury or death.

 

CAUTION

This indicates a hazard which, if not avoided, 

might result 

in serious injury or death.

 

NOTICE

This message presented without the alert symbol indicates 
a situation where the unit or property could be damaged.

Not 

for  

Reproduction

Содержание CCW36 Series





















































Отзывы: